Hello,
For sale is an Aeromotive A1000 pump with 12304 and 12340 filters. Includes extra 10 micron filter for gas use (e85 installed).
These were mounted, but never activated (no fuel ran through them).
$800 shipped within continental U.S.
Thanks for looking!
Hello,
Does anyone know if Glenn's Performance is still making tanks for the 1995 Cobra R? Didn't see anything listed on their website.
Sent them an email, but didn't hear back.
Thanks in advance!
Hello,
Up for sale is a Colgan bra for 1994-1995 Cobras (may fit years 1996-1998, however not sure about this).
This is still in the plastic and was never installed/used.
I only ship within the continental U.S.
$150.00 shipped
Thanks for looking!
Hello,
Up for sale is a Florida 5.0 gauge cluster for 1987-1993 Mustangs.
Will accept four 2 5/8" gauges.
$90 shipped (I only ship within the continental U.S.)
Thanks for looking!
Hello,
Up for sale are multiple Auto Meter Ultra Lite Pro Comp gauges. These were in my project car that was never finished.
Gauges are 2 5/8" (except 5" tach).
Prices are as shipped (I only ship within continental U.S.)
All gauges sold!
Thanks for looking!
Hello all,
I am replacing radiator coolant (engine not intercooler) and I will be using a tool similar to the Uview 550000 that uses shop air to create a vacuum in the engine to backfill with water/coolant.
I know some folks have used this with great success, but I was wondering where these...
O.K., I haven't seen much when I do a search...
That being said, where in the hell do we find space to put a Bob's Oil Separator in the engine compartment? I'm looking and I can't find the amount of room necessary.
Anyone?
I need to get the roof fixed on my '03 Cobra.
Body man says that to do the job right, he would need to pop the front/rear windshields out to get underneath the rubber windshield trim pieces.
I'm not too cool with that because to reinstall the windshields, videos I've seen shown using a metal...
Hello,
Up for sale is a lowering kit off of my 1995 Cobra. Included is a Saleen spring kit (lowered my car a little over an inch), Kenny Brown caster camber plates, and bump stop for the rear. Kit has about 7,000 miles on it.
Springs + bumpstop SOLD!
Caster Camber Plates w/Hardware $75...
Hello,
Up for sale is a performance exhaust for 1994-1995 Mustang GT/Cobra.
Included is a set of Hedman Jet Hot coated stepped headers, off-road x-pipe, and Flowmaster catback system with hardware.
Started to cut through catback system to get off car, but stopped before cutting through tubing...
Hello,
Up for sale is a Stiegemeier ported Eaton, elbow and throttle body. It has about 12,000 total miles and 2,000 miles with the port.
Billet Flow pulley included.
SOLD!
Thanks for looking!
Does anyone know how to clean/restore the OEM rubber intake boots on the foxbody Mustangs?
Most of them take on a white stain over time.
Included a pic of mine to show everyone what I mean.
Hello,
Looking for stock catback from a '87 - '93 GT.
Need a set with no than 15,000 miles on them.
I know someone out there has to have these lying around from an install long ago.
Thanks in advance!
Hello everyone!
Title says it all.
I know someone out there has to have a take off system they're keeping in the back of their garage from a project long ago. Looking for something commensurate with a 10,000 mile car.
PM me what you have!
Thanks!
Hello,
Up for sale is a C&R heat exchanger kit for 2007 - 2012 GT500s.
Bought from Revan Racing and removed from car with less than 1,000 miles on this piece.
SOLD!
Thanks for looking!
Hello,
Up for sale is a Ford Racing Performance Parts TVS part #M-6066-TVS for '07 - '10 GT500s.
Supercharger had about 1,000 miles on it when pulled off my 2010 GT500.
Pulley is stock.
SOLD!
Thanks for looking!
Hello,
Up for sale is a Stiegemeier ported Eaton off my 2002 Lightning. This piece has about 10,000 miles on it when I pulled it off of my truck. Ran great when it was removed just recently.
SOLD!