It has come that time to sell and perhaps move onto another toy. I have really enjoyed owning the car over the last 9 years, but I really haven't taken advantage of driving it much. The car is as you would expect for a garage queen 36K mile car. Exterior wise I would rate the car 9/10 and...
What's the status on this? I believe MalcomV8 was working on integrating the GT500 heat exchanger in the 03 Cobra along with a few other goodies to help combat the heat issues we all experience. I have gone down the road of the Killer Chiller and all that did was create a/c issues (leaks)...
Anyone have the old clutch install write up that was in the How To section? I can't seem to locate it anymore and I need to get the torque settings for the bolts.
Thanks
Mike
Sent from my iPhone using the svtperformance.com mobile app
So what's the verdict on this? I know with going with valve cover breathers you will get fine oil mist on the motor, but it definitely keeps the garbage out of the engine. I am leaning this direction as there is less hoses running around the engine bay, but just looking for suggestions...
I just spent about a $120 on one exhaust manifold bolt (h-pipe) and 4 new rubber exhaust hangers! It's crazy what the prices are now as these pieces become obsolete.
It's been a while since I have bought parts for my Cobra and I am finally interested in it again. Who is the best Ford dealership to work with to get Ford parts? I need some exhaust hangers, exhaust manifold gasket, and exhaust manifold bolts.
Thanks,
Mike
Anyone had this done yet? I want to get mine refinished and also the tears widened out to 18x11. I believe I should be able to add an inch to the inside of the rim. Thoughts?
Sent from my iPhone using Tapatalk
Just as the title states. I got a custom Chiseled Performance tank forsale that fits in the rear tire well. Its got 2 one inch outlets with Jegs fittings and one half inch outlet for a drain. The tank is painted black and is 5 inches x 16 x 14. It probably holds a little over 4 gallons...
So i was taking my side skirts off so I can get them refinished and didn't realize that the black strip on top of the side skirt under the door held it in! So in short all the little tabs broke when I pulled the skirt off. Is it trashed or can I just epoxy them back?
I must be getting old as I want to quite my cobra down some. I have an off-road h-pipe into 2 chambers flows currently. I swap out the h-pipe for the pro-chamber will that be quiter than throwing on some of the high flow cats from Magnaflow? I don't want it super quite just a little tamer.
Just trying to get an idea of what would be an average amount to pay to have my factory front bumper and hood repainted? Also thinking about getting the sideskirts and louvers on the side redone since they are quite yellowed at this point (silver metallic is my car color).
THanks,
Mike
Well back about 6 months ago or so when I was installing my rear mount tank I stupidly drilled a hole in the top of my gas tank. It's a small hole (size of a pen tip), but any ideas on the best way to fix it?
I have a custom water tank in the trunk for the intercooler system and I can't get the damn thing to stop leaking. If I leave the pressure hole open on the lid it shoots the fluid out and if I seal it up it leaves around the lid itself.
The factory intercooler tank is still up front and...
Once again my mezier pump I am using for my intercooler system has killed off another bearing in it. There is maybe 750 miles on the pump since the last time I had to get it fixed by the manufacturer. Now its out of warranty and I believe the fee is $100 to fix. This is going to further the...
I just installed their 26 spline 725 horsepower clutch set up (organic on 1 side and ceramic on the other) and so far I gotta say....I LOVE IT...The pedal effort is half of the factory clutch and there is absolutely zero chatter. I am still playing with the adjustment of the engagement as it...