Search results

mustang with black wheels and yellow calipers. Thinking of doing my calipers yellow instead of black.

in gloss black vinyl?

I bought some and I can say that it works as advertised. Dries to the touch and withstands the elements. I would say that it lasted about two weeks even though it rained for a week or so. Sprays on with aerosol can like paint. Would recommend it, was using Black Magic tire gel.

Installed meter4it kit and everything was fine. Now the furthest right bulb on the passenger side only comes on with lights and brakes, doesn't work at all with hazards or blinker. I've done the obvious like change bulb, check fuses, check wires for frays, make sure metal connectors are pushed...

Just got the car back, will post more when it is cleaned. Yes the plate is there. I live in Tx and have to have front plate. It hasn't caused any problems yet.

Where can I find headlight molding/trim to replace my torn ones?

but kept door jams original color. My question is, would it look acceptable to say, paint an all black car chrome yellow with black accents such as wheels and blacked out tails and leave the door jams black instead of having them painted chrome yellow. It will have the black and yellow theme...

My compressor clutch stays engaged even when the knob is turned to off. Could it be a wire short issue? I've replaced the low pressure switch already. What could it be? Thanks

The compressor clutch is always engaged, it never goes off no matter what the control knob is turned to. What could be the issue? Could it be a ground issue, like a bare wire or something? Thanks

First off, no hassles about my front plate location, lol. I live in Tx and it is required. I haven't been harassed by the police so far and it doesn't obstruct any air into the radiator or intercooler. On with the pics.

Long story short, my wife backed into my car and destroyed my side scoops so I replaced them with Saleen ones. How did you get them to stay attached at the bottom by the side skirt? The instuctions said to use double sided tape but it doesn't hold good. There is a little gap. Any help is...

Anyone have a step by step on removing the old one so I can change it out? Thanks in advance.

Anyone have a step by step on removing the old so I can change it out? Thanks in advance

Anyone have a step by step on removing the old so I can change it out? Thanks in advance

How long/miles do they typically last?

Is it a tickable offense to have a clear plastic cover on your liscense plate or mount your front plate in the grill? I was pulled over and let go, but would like to know if someone else could give me a ticket for this. Does it state in the law that the plate must be mounted on the bumper...

Where can I get center caps for ssr gt3's? I know they are discontinued, but can I still get the cc and where? Price? Thanks

Those of you that live in states where a front plate is mandatory...let me see how you display it other than drilling holes. I don't want to drill my bumper.

I've decided on 17 inch wheels. Need help choosing between the two, help me out. I like them both.:-D

I'm trying to decide if it is worth getting 18 inch wheels or not. I want to see some nice 17 inch wheels. :banana:

Can a tune go bad or become undone? What else can cause drastic loss in power and torgue. Some background info: I have an 02 gt that has had a PTK kit on it since 03. My initial numbers were 430 and 505, the tune was done by Murillo so I know it was dead on. Since then I have added an SLP...

I searched but couldn't find an answer. Will foglights from an sn95 cobra fit into an 01 front bumper? Are they the same size? I want to buy the clears from BOI and for the sn95 and swap the lens to my fogs. Thanks in advance

Will 03/04 cobra fog light lenses fit 99/01 cobra? I want clear fog light lenses but can't find them anywhere that are good quality. Will they fit? Thanks

Where can I find the clear fog lights for 99, 01 cobras?

with projector headlamps. How do you like them? How is the light pattern, is it clean or are there hot spots and glare? How did you adjust them etc. Any help would be appreciated. Thanks in advance.