Search results

Looking to sell a set of TMI pro viper Jr. seats in “parchment” out of my 2013 mustang. These seats should fit the 2005-2014 body style. Brackets are included in sale. Not looking to ship but will consider shipping if buyer pays. Very low miles like brand new. TMI Products Pro-Viper Jr. Sport...

Hello I’m looking to purchase some take off Recaro seats from the 2013-2014 model. I’m interested in either the black leather or boss 302 editions. Let me know if anyone has or knows of any for sale. Thanks.

Does anyone have any opinions on catch cans for 2013 - 2014s with a TVS blower? I’ve been looking at the typical JLT passenger side one for vmp/roush application. But recently I started to consider something from UPR or Bobs Catch Can. Can anyone shed some light on what they use? Do you use...

Looking to sell my used Accufab 84.5mm Throttle Body. Reason for selling is because i went to a TVS blower. Looking to get $425 shipped for it. Please PM me if interested. Thanks Accufab Mustang 84.5mm Throttle Body (11-14) 5.0 F845

Looking to sell my Boss 302 intake manifold and setup with other intake aftermarket parts as shown below. If interested in it all I will let it go for $1200 shipped (US) otherwise the prices for each are listed below. Each price is shipping included. Thanks Ported Boss 302 Intake Manifold -...

Has anyone else had the issue of their steering wheel controls not working as well as when they first got their mustang? My steering wheel controls will work when pressed sometimes and it is very dependent on how they are pressed. The most finicky one being the "OK" button on the left hand side...

I recently purchased some TMI racing seats for my 2013 premium package mustang. I was wonder if anyone has attempted, or knows if it’s possible, to remove the heating pads and electronics from the factory seats to be put into the aftermarket racing ones. Also i would like to transfer the...

I am interested in purchasing the drivers side headlight housing for a 2013-2014 if anyone has one laying around. I just would like the housing, not the bulb or accessory hardware. Thanks

I just recently purchased the BMR K member with the 1/2 inch lowered motor mounts. Does anyone have any experience with this set up? Any issues with scraping the oil pan or anything like that? Thanks

I usually drive my car with the autolamp feature on with the toggle pulled out to enable fog lights when my headlights turns on at night. Today while driving in daylight my lights (headlights, running, fog) began flickering continuously, I could hear the ticking noise coming from the passenger...

Recently I noticed that my drivers side headlight would get repeated condensation on the inside of it. But after a while it began to almost become foggy permanently on the inside. I have looked around to try to find a replacement housing to just transfer everything over to it. But I havent had...

Wanting to sell my old MT82 transmission with clutch and flywheel all with 55k miles on them, never tracked or raced. The trans has fifth gear grind every now and then. Needs to have synchromesh replaced on it. Looking to get $500 plus shipping for the whole thing. Thanks

Bought these in a sale from another user but will not be using them. They are brand new taken off of a 2018 performance pack car. The brakes are 15" rotors, looking to get $100 bucks plus shipping fees. Thanks

Looking to sell 4 piston brembo brakes on car as I am going to be upgrading them. Sale will come with 2 4 piston front calipers, 2 z23 evolution sport ceramic pads, and 2 power stop drilled and slotted rotors for extra shipping cost. Looking to get $450 shipped and if rotors are wanted as well...

Looking to upgrade my front brakes with a set of 2015+ 6 piston performance package calipers. If anyone has any to sell please let me know. Thanks

Does anyone know which diff cover will allow me to relocate the bleeder nipple from the drivers side axle to the top of the diff cover? Allowing me to plug the bleeder on the axle so that it stops leaking. Thanks

As the title says interested in purchasing a boss 302 steering wheel message me with details.

So i currently have a set of Dynatech LT headers w/ a catless x pipe sitting in my garage. How much RWHP should i expect to see after i install them and get a good tune? My car sits as a 2013 5.0 6 speed manual with a ported boss 302 intake manifold, accufab 84.5 mm throttle body, 101 mm steeda...

Looking to buy either ARH, kooks, or stainless works LT headers w/ preferably catted h pipe but would be interested in the catted x pipe. Also would consider catless if the price is right. Thanks.

So I noticed recently very randomly a weird scuff mark started to form on the top of my steering wheel. I believe it was due to heat being on it and then my hand being placed in the same general area. Any idea how to fix it or would I need to replace the steering wheel totally.

So its time for me to get a new set of tires. I am currently running the niche gt5 with 20x8.5 front and 20x10.5 rear, and i am also lowered 1.5 inch. I am looking at doing a set of 305/35/20 on the rear and a 265/35/20 on the front. Would this set up run well? Also the tires i am replacing are...

Interested in a little project. Does anyone have a pair of upper and lower grilles for the v6 13- 14 model with the black surrounding? If so text me a picture to 7138552042 thanks!

As the title says. Interested in a roush lower grille. Text me with a price and picture please! 7138552042

Does anyone know of how this grille was made or who makes it? Really interested in trying something like it on my 2013 gt. Thanks!

SOLD Want to sell a used 3dCarbon gt500 Rear Spoiler, has been on car for about 5000 miles. Reason for selling it is because i wanna try something different. Painted in Deep Impact Blue. Was $330 new asking $250.