Search results

Doing a remote dyno tune with lund. I was going to tell them 6500 max rpm

Having cams installed in the car. Going for 750ish rwhp. Will my rods hold up? Car has frpp 65mm tb, jlt 123 cai, Detroit rocker cams( going in soon), killer chiller, colder plugs, and only runs vp c10 fuel

The new ge tier 4 prime mover is a v12 runs at 950 rpm in 8th notch. Turbo speed is around 23k. But nothing in the display screens show boost psi. Im a locomotive electrician and ive been trying to find the boost psi too.

Yes the car has cats. I will get a video in a couple days. It's cold her and the car is in the garage.

So I've got a thunk noise. Can be heard out the tail pipes from underneath and under the hood. The noise only comes to life after the car is almost warm. Hard revving sounds fine hard acceleration fine. Oil level is ok. Car is not throwing codes. Car has 5k on it. Has ar headers borla mufflers...

So my whine is a pinion/ ring gear issue I take it from the comments. If the carrier bearing was spinning in the bearing bore or damaged would it not be a whingeing nose?

What kind of upgrades would prevent this. Have no idea other than changing gears.

Post should have said jlt and frpp not my miss spelling lol. Arh headers 1 7/8 primary's. Maybe I will take it into Ford. Purchased the car November 2013 so 5 year powertrain. I do drive the car hard minus hard launches. So if they fix under warranty so be it. Idk

So I've had my 14 gt500 for 5 year bought it new 5 miles on odometer. Today I was taken the car for a ride to a friend's house to put headers on. So the rear seats where folded down because of the parts in the trunk. And I hear a wine coming from the rear end ugh. I have never launched the car...

Has anyone installed a killer chiller on a 13 14 Shelby. There are almost no instructions with the kit. Any pics or tips would be great.

Did any of you guys have to drop the k member for installation or use a flexable dip stick tube?

Thxs. Anyone have dynatech headers

Going to put headers and a x pipe with hi flow cats on the car this spring. What r the best headers and hi flow cats/x pipe out there. Looking for good fitment and cats that are not garbage?

Im going to change my cluch. My dyno run was over 650tq. Dont know how long the stock cluch will hold up. Need to know what cluch i should go with Spec, mcloud, center force ect. Was going to go with a spec twin disk but seen some bad reviews online. The cluch breaking after 2000 miles. So what...

Thanks, im looking at a rtr wheel from AM its 20x10.5 it look just like stock and i think the offset is 47.

What is the offset of stock wheel?

By stock look i mean the same looking rim just in a 10.5 or 11 wide

Yes catmonkey you are correct. Plus after looking at the tech spec i see it does not fit with the brembo brakes. Was looking to get a wider rim on the rear of the car but keep the stock look. Any suggestions?

Not sure what the offset is the sit just shows the pic of the rim and size. Nothing about offset.

305

I have nitto 555r on my stock 20x 9.5 inch rear rim. The tire is not getting all of its tread to the ground this i can see by the wear pattern. I see that America muscle has the svtpp rim in a 20x 10. Would this help the tire get all the tread down? And would i have to worry about a offset...

Looking for a x pipe with hi flow cats that will bolt up to my stock manifold. But i am also looking for one with very high quality cats. Any help would be appreciated.

Going to have rear tires installed and can't find the wheel lock for the locking lug. Called the dealer and was told that they are factor installed and the lock is put in the car at the factory. Was told to look in the trunk and glove box. Ive looked all over the car. Have a air compressor in...

I come across posts about whining noise in rear end or carrier bearing issues in our 8.8. My question is how many people are having these issues? I am about to have a set of nitto 555r's put on this Friday, tired of my car not having any traction. No issues yet but putting on the dr's does...

Going to change out my back tires. Was thinking of going with nitto 305 35 r20. Will they fit on the stock rim? I've been told they will but i would like to hear from someone using them. And if so how do you like them? Thanks.