Search results

located in Sacramento Ca hi, I am looking to sell my 2004 cobra convertible. It currently has 73,000 miles. No accidents and a clean title. The color is Red Fire Red. Top is in near perfect condition. The nearly 4 years that I have owned the car it has lived in the garage. yes it has been...

So I am looking to sell my 04 redfire Vert. It currently has 72,000 miles and has the following mods: 10.5" cobra rears with 315s H&R rear springs with UPR coil over up front Koni yellows around BF idlers and 2.8 metco Aed tune JLT ran intake JLT oil seperator LFP gen2 head cooling mod MM...

Hey all, I was almost finished with my LFP Gen2 head cooling mod install when I lost the bolt that holds the bracket to the back of the head. Does anyone know what size bolt goes in there? I want to be able to pick one from the hard ware store tomorrow so I can finish this job. Thanks

Hey all, I installed a new centerforce DF clutch, Fidanza flywheel and ford TOB about 6000 miles ago. recently my clutch pedal shakes and rattles vigorously at idle and while driving in all gears. I am running a stock cable , Steeda quadrant and firewall adjuster. if I loosen the adjuster i...

I'm looking into running some 13' gt500 waffle wheels on my 04' thinking of going 18x9 up front and 18x10 in the rear. Curious on how it would look on my red fire vert.

So I went to throw on my UPR coil overs and when i slid the sleeve on they do not clear the strut mount. Is it supposed to fit like this? I am running the koni adjustables. Should I notch them to sit flush? I know the kit specific for the bilsteins is different since the tubes are smaller...

What is this belt called so I can go about ordering a new one? And how how do you replace it? Does anything have to come off to get to it, or is there any special tricks? Came home and when i pulled onto my street I heard what sounded like gravel being run over, but under the hood. When I go...

So I just got my car back from AED Tuning. my car with below setup put down 466hp/485tq @5700rpm jlt cold air boral stingers magnaflow catted x 2.8" metco billetflow idlers jlt oil seperator Correct boost bypass mod KB BAP 170* reisch thermostat RP 5-30 HPS oil in the engine and eaton...

So ive been doing some searching on this matter and hear that a super tight belt is ok, and then I hear it is not due to the posibility of adding extra wear and tear on bearings. I threw on my billetflow idlers and 2.8" metco upper. Billetflow's website calls for the stock belt with this...

I have a gates green belt that has about 30 miles on it. Purchased it before I changed up my pulley combo. Won't work with my new setup. asking 30 shipped.

Hi there, im selling my brand new Accufab plenum and freshly recalibrated (from accufab) throttle body. Comes with throttle body gasket, iac sensor gasket and a TPS. Looking to get 400 shipped for the combo.

Hey guys, Did some searching but haven't seen any exact answers. I currently have a 2.8 metco upper installed and im about to have the car dyno tuned by AED. Im wondering if it will be worth the extra few bucks to squeeze any extra boost out of my stock Eaton with a 2.7" before the tune. or...

I have one of these in my 94 landcruiser and it works great for monitoring the temps. It can be used with a radiator adapter or drilled and tapped into a bung. Im wondering if anyone on here has one, if so where did you put the sensor? and where did you mount the readout? Im curious if the...

Hey guys I was hoping that someone on here may have a pulley puller/installer tool that they are willing to rent out to me. I know billet flow rents them out for 80 but that's pretty expensive. I'd drop a deposit and pay for the rental. Id only need it for a weekend. Much appreciated. Thanks Eric

Any convertible owners out there have some pics of where and how they mounted their boost a pump? All the pics I can find are of coupes. Any input would be appreciated. Thanks

Ok guys I've read so many damned threads about the boost a pumps. I bought a used BaP from a local guy. He told me it was on his 03 cobra. Come to find out it's a 20amp model stamped (15). I've read things saying it will work with my stock set up and read things saying it will not work. What...

Im wondering if running a 74.5" belt will be fine with the 2.80" metco pulley and billet flow idlers. BFs website reccomends a 74.5" with their. 2.76" pulley and idlers. Do you think the .04" will make any difference? Thanks in advanced.

hey guys I have a 20amp kenne Bell Boost a Pump for sale. It is in perfect working condition. it is set up to be on all of the time. Pm me if interested. im asking 125 shipped. thanks

Hey guys I have a 20amp kenne Bell Boost a Pump for sale. It is in perfect working condition. I have since sold my 97 cobra and it will not work with the set up on my 04. it is set up to be on all of the time. Pm me if interested. im asking 125 shipped. these are around 250 new. thanks

Hey guys I have a freshly re calibrated and polished Accufab single blade throttle body and brand new Accufab inlet pipe. comes with all gaskets including an extra throttle body gasket. I will also include the TPS pictured. I have not put any miles on this setup yet since I got it all back...

Hey guys I have a 1st gen JLT cold air intake for sale. It is in good shape. the filter is a bit smashed, but does not effect the performance. There are a few scratches around where the intake goes into the fender. comes with everything seen in the ad. I am asking 150 shipped...

hey guys, did some searching with no answers. just did a clutch and flywheel swap on my 04. Got everything all buttoned up and went for the initial start up. Let the car warm up and idle for about 10 minutes. It was running very rich and was jumping from 600-800rpm almost non stop. Went...

has anyone removed the Cross member off of the front underside of their cars? Im having some rubbing on speed bumps and some roads at higher speeds. any noticeable difference after the removal? i currently have Sub frame connectors to maybe make up the difference. thanks guys

Hey guys. So I just installed some h&r sports, with maximum motorsports C/C plates on my 04 vert. I kept the isolators in on the front and rear. I'm Getting major wheel rub on the passenger wheel wells. I'm running a 275/40/17. Anyone else have this problem? Any suggestions before I...

hey guys. trying to figure out what my next performance mod should be for my 04. its currently stock with borla stingers, SCT canned tune and a steeda shifter. im currently running 275 nitto555 up front and 315 in the rear. I have some pro kit springs on the way. so i have a pretty clean...