2011 mustang GT Hellion twin turbo
I have On3 triple fuel hat w/3 walbro 450 pumps.
The problem, I have to use POR sealant or other epoxies to seal the wiring coming/going through the hat and no matter what my interior always smells like gas.
Surely someone sells a triple hat, walbro...
2011 GT TwinTurbo.
Just trying to figure my best options(price/ quality)?
Preferably in Florida, but at this point shipping is shipping I guess.
... I've seen builders specializing in mt82 here on SVT, I haven't seen recommendations for T56, and I'm sure there has been.
Thanks for any / all info
2011 GT, Twinturbo, t56.
The description for this code is= "Throttle pedal position sensor switch A B voltage correlation".
I've been searching for a couple hours I'm not finding exactly what I need to know.
Driving home today I got the wrench light, and throttle what's not very responsive, and...
After 162,000k miles I decide to replace my OEM coils with some MSD Blaster coils. The first day I get a misfire I threw a code po353c telling me that number 3 coil is bad. Put the OEM coils back and it works like a charm. I call MSD and say dude your crap is not working and they say oh we'll...
2011 mustang GT HellionTT
I've been running this kit on my Built 5.0 successfully for 2 years now.
I run 8.8lbs on 93
I run 12lbs on 93 + VP octanium (or Torco)
Anyway I had a bullet bike come up behind me Saturday, on a long desolate stretch of road, I can easily beat most bullet bikes i...
"Volts, not "bolts"
Sorry guys I know that,
The brown wire is falling voltage
The brown wire is the wire used for WOT switches(other than Zex switch).
The green/purple wire is rising and reads WOT @half-throttle.
Etc, etc.
I've read and read, but what I don't understand is the phrase "falling...
2011 mustang gt.
I have a project that I'm working on and I need an RPM switch that I can signal, preferably, off of a coil. It will operate a solenoid(.45 amps/12v). I purchased a Summit RPM switch, it was defective, they sent me a replacement and it was defective as well(LED didn't work). So I...
Manley 11.0:1 (+3.75cc Dome) stock compression pistons. 3.635" bore. New never taken out of box. I purchased these and then used a different piston all together so here you go, your gain, selling cheap. As you can see by the pic they were manufactured 5-2-17. Comes with Wrist-Pins and C-clips...
I have a Hellion twin turbo with two 55mm turbos(Precision/journal). After one year the bearings seem to be going out. Opposed to rebuilding them I'm thinking of going with ball bearing turbos and possibly Garrett Turbos.
I've changed my oil every 3000 miles I use mobile one synthetic, I'm...
I installed a T-56 Magnum Transmission in my 2011 gt so I no longer need this MGW shifter. You all know about these shifters. I would have swapped to T-56 two years ago if it weren't for this shifter. With the White Brothers trans mount insert and this MGW shifter it stopped all of my...
I'll see if I can add pics.
I've used this DS on my 2011 DailyDriver for the past year, I installed T-56 transmission a month ago and had to purchase a different one-piece. I wanted to keep it, the MGW shifter, and the MT-82 for back up or whatever(I hoard things) BUT i need the $ after buying...
After adding the approx 80-100lbs of Hellion TwinTurbo I've noticed front dropped an additional 7/16" on my already 1" lowered Eibach Pro coil springs. I've ordered Energy suspension (3/8" thick) coil spring insulator/pads to go between the strut tower and the spring. I'm wondering if a stronger...
Cylinder 1= 150
Cylinder 2= 150
Cylinder 3= 122
Cylinder 4= 140
Cylinder 5= 130
Cylinder 6= 120
Cylinder 7= 150
Cylinder 8= 145
What do you think?
Compression test was done correctly on all cylinders= Disconnected fuel pump, ran gas out, disconnected coils, pulled all plugs, held throttle to...
2011 GT, Hellion TT, ...Driver-side WG gets hot as soon as car is started, BUT the passenger-side WG takes a little while to warm up(hasn't even fully changed color like the DS, still silver'ish). And then when it gets hot it's half as hot as DS= as in I can still touch it for 2 seconds....the...
I ordered my wastegate with my TT kit with 7psi springs, equating to about 10lbs of boost. Because 10lbs of boost is what I want. Well, I've recently read that if you want 10lbs of boost that you should purchase wastegates with lighter springs so that the gate can start opening early enough to...
I've called Hellion ,no one that knows vacuum is available, I posted this on power-adder forum couple hrs ago and 97 views later I get 1 response. I have a Hellion TT installed, ready to crank, took off work today so that I could crank it, been waiting 4 hours on a return phone call to confirm...
I figured some of you TT veterans could help me here= The instructions say to remove passenger side crankcase hose from 90° fitting so that you can use this for vacuum/boost, etc. Well I don't want to put a simple breather on the passenger side valve cover, I actually want to use a...
Threads in crank aren't the best(happened during last build)but threads are re-tapped and this time I made a damper install tool (12x1.5mm all thread, spacers, and 12x1.5 autograde lugnut).
My question= when do I know if damper is fully seated? I cannot keep torque'ing nut in fear of...
I built my 2011 5.0 in dec of 2013. I recently pulled it to do some crap(timing chain, phasers, etc) before I install Hellion TT. I'm changing the timing chain cover because it has hair-line fractures in it from factory(that I plugged up with Motocraft TA29). But look at the pic, at the oil...
I've yet to install my TT in car(engine out going back in next week), but because I've never had a full engine compartment like this which catch-can will work best for Hellion? ...I didn't want to purchase one and then have to engineer hose so that it will fit around TT. (I searched but nothing...
2011 gt, I've read and read on this topic(Intake air temp sensor) but can't seem to find this info on 2011-2014. I know to install sensor after intercooler/before intake. But I'd like to ask someone with this kit from their experience where and how the best location for sensor. I thought I'd ask...
I have 2011 gt. I need a new timing cover. The a/c belt sucks putting it on and taking it off. I read something on LMR about the 13-14 gt were changed to have a tensioner for a.c.. Is this true?
Thanks
2011GT, I built my motor Dec 2013, I used all ARP bolts that I thought I needed(head, crank, main, rod). I'm seeing a lot of talk about Cam Cap bolts. I now know the factory Cam Cap bolts are Torque to yield. So plz, since I reused my factory bolts, let's talk for a sec. ...I understand the...
2011 Mustang GT, I remember when I built my engine that I almost messed up the threads putting the harmonic balancer back on so I re-tapped crank threads. I'm about to pull motor again and this time I want to use a balancer "install tool". So if I knew the thread and diameter size of crank bolt...