Search results

  1. J

    Whipple supercharger noise Help?

    Just a thought…If the tensioner is clocked in the correct position for a specific belt type, RPM flutter should be reduced because, correct tension is being applied. If going with an RPM belt set it at 40%. An RPM belt set at 80% (incorrect tension) will cause it to snap that is what started...
  2. J

    Whipple supercharger noise Help?

    SW, That is the way I had the belt run originally…But…….. When Whipple updated the tensioner they updated the belt routing system. Basically, they went back to the way Ford had it with the exception of the supercharger setup. Here is a picture that Fishpick provided. This picture shows the...
  3. J

    Whipple supercharger noise Help?

    Hi ..SW Thanks for chiming in. Whipple sent me a new belt tensioner and everything is working fine now. The first replacement belt tensioner was defective. No more noise. I’m still not sure why they updated the belt routing. I read through Fishpicks belt tensioner threads and I’m trying to...
  4. J

    Whipple supercharger noise Help?

    Finally, found the problem. The belt tensioner has a damper inside that is no good. Here are two additional Youtube videos that show us checking for the noise issue. Hope this helps others who may encounter belt tensioner noise.
  5. J

    Whipple supercharger noise Help?

    Update Just want to share incase anyone else runs in to this issue. The idler pulleys mounted on the plate below the supercharger pulley have side play. If I remove the belt and I grab each pulley one at a time they have a very slight side-to-side wiggle. Looks like two of them wiggle a bit...
  6. J

    Whipple supercharger noise Help?

    Last week the serpentine belt broke leaving me stranded on the road. The original serpentine belt was a KO60891RPM. I spoke with Whipple and they sent me a new belt tensioner and serpentine belt KO61066. Just finished the install. Tension is correct. The belt mounting plate and the job went...
  7. J

    How do I remove a 2013 HID light bulb?

    Found the answer at LMR. Thanks!
  8. J

    How do I remove a 2013 HID light bulb?

    Hey all, I’m trying to figure out how to remove the passenger side headlight HID bulb. Yes, I did the Google/YouTube search. Not a whole lot of info on it. After removing/turning counter clock wise the access cover ,….. I’m seeing two phillips screws top and bottom looks like they are...
  9. J

    Whipple 2.9 install, finally finished

    I’m using the Whipple Tune. The car runs amazing. No surging, etc. Of course I have only driven it six miles at this point. I’ll have more to report later in the week. My goal was to have a tight performing street car that would pass NJ emission inspection. Trying to squeeze the last 10th of a...
  10. J

    Whipple 2.9 install, finally finished

    Thanks everyone! I have built 13 muscle cars in the past. (Yea I’m an old timer) This is my first Super charged project. Riddick the catch can… line loop is ok….. it is just an aesthetics thing. I’m still working my way around a few fittings. The 10AN line is hard to bend with out kinking...
  11. J

    Whipple 2.9 install, finally finished

    Hey all, I know a few of you have e-mailed me regarding the 2.9 install. I finally finished a week ago. NJ weather sucks, so I only had the opportunity to drive 6 miles (yes a trailer queen..lol). This week I’ll have it out. Here are a few photos. I want to thank Fishpick for helping...
  12. J

    Adding coolent/antifreeze to Whipple Supercharger air in system Help???

    Thanks DSG. Just filled the intercooler circuit. Waiting for the vacuum purge and refill kit to get the air out of the engine etc, before refilling that system.
  13. J

    Adding coolent/antifreeze to Whipple Supercharger air in system Help???

    Hey all. Ok the dumb question but, getting frustrated. I just installed a Whipple 2.9 Super Charger on my 2013 Mustang. I also installed a Ford Performance GT Radiator. Question…In addition to filling (adding coolant) the degas bottle…Do you fill the Intercooler filler neck which is attached...
  14. J

    fishpick's 2012 Coyote Vert Build Thread (Base GT Convertible)

    Opp's Just figured it out....I don't have the super charger installed yet. Been waiting on parts from Whipple,...so I have been working around it. Getting ahead of nyself. Joe
  15. J

    fishpick's 2012 Coyote Vert Build Thread (Base GT Convertible)

    Hey Fishpick, Hope all is going well with your 2.9 Question…I’m finally back on the whipple 2.9 install. I had to wait on a few items I was short on. I have been working on this thing all day. I’m having a brain freeze. I just installed the inter cooler filler neck on the side of the air box...
  16. J

    Damper Bolt??/Project hold up

    Thanks, I called MMR they said the stock damper bolt is fine. I order a new bolt and the installation bolt. They are in the process of making their own (MMR) damper bolt for the (Coyote 5.0) application.
  17. J

    Damper Bolt??/Project hold up

    Yea, I called them/e-mailed them no response. Went through every vendor A through Z nothing. I was told nation wide back order. I can get a Boeing 787 built faster then an ARP bolt. ...(pissed) ok I'm off my soap box.
  18. J

    Damper Bolt??/Project hold up

    Hey all, Project hold up…. I’m still in the process of installing my Whipple 2.9 supercharger on my 13. I finished the oil pump gears etc. I have been waiting several weeks for a back ordered (I’m told since Feb) ARP damper bolt. The date continues to get pushed back. (July/Aug). Ok...
  19. J

    Billet oil pump gears

    Last weekend I just installed Boundary oil pump gears in my 2013. The gears are awesome high quality. I had written to Boundary regarding their gears (see below). I run a super comp car on the weekends (ok a Chevy) and have talk with many Mustang owners at the track who run Boundary gears...
  20. J

    fishpick's 2012 Coyote Vert Build Thread (Base GT Convertible)

    Fishpick, I just finished the oil pump gear install. Getting ready to install the 2.9 Whipple. Thanks for the OPG write up! Very Helpful!! I just ordered the same radiator and electric fan set up you have. Just wondering what weight motor oil are you using? Yea, I know the oil threads...
  21. J

    Whipple/fuel injector supply manifold pressure release.. How?

    Hi All, I just finished installing my oil pump gears now I’m getting ready to install the Whipple 2.9 on my 2013 Mustang. The car is currently apart (cooling system, etc.). The Whipple instructions say I first need to make sure fuel injector supply manifold pressure is released. I can’t run...
  22. J

    fishpick's 2012 Coyote Vert Build Thread (Base GT Convertible)

    Fishpick, Glad to hear things are moving in the right direction. My 2.9 install is coming along. Do you have the size or, part number for the replacement (shorter) belt. Thanks!!
  23. J

    fishpick's 2012 Coyote Vert Build Thread (Base GT Convertible)

    Hey Fishpick. Thanks again! Joe

Top