Search results

  1. dazwelding

    Belt issues

    I am continuing to tear up supercharger belts- IE: shred one rib off of the belt, and I am looking for input on what the cause may be. Here is what I have done/found so far: Going back to the beginning of this issue was July of 2021 when I got home from the Dyno. I drove her home from the dyno...
  2. dazwelding

    VMP Intercooler, VMP high flow manifold VMP Triple Pass HX, PNR Trunk Tank, and EMP Pump

    I am installing all new cooling system for the supercharger. Thought you would all enjoy the pictures.
  3. dazwelding

    ECU Protocol

    What ECU OBD2 Protocol does our stock computer have? (2003 Ford Mustang SVT Cobra). I am trying to datalog with my Aim Solo 2 DL.
  4. dazwelding

    Harmonic Balancer, Crank Support, Lower Pulley

    My supercharger belt got tore up (one tooth of the belt), and the diagnosis is the lower pulley bushings are shot. As a result, I am attempting to purchase a new balancer and lower pulley vs just replacing the pulley alone. My standard MO is “while I have this apart I may as well replace...
  5. dazwelding

    ABS not working

    I have installed 07 GT 500 brembos, stainless braided lines, and New stainless hard lines from front to rear of the car. I went to bed the brakes and the brakes locked up like there is no ABS. I thought I needed to bleed the ABS unit, so I purchased a scan tool, Autel MaxiCheck Pro, that runs...
  6. dazwelding

    Aftermarket Gauges- Speedhut

    I have made custom gauge clusters (I must brag it is quite beautiful . I will post some pictures) and I am working on the wiring of the gauges now. I am sure I may have more questions but I will start with what I have stubbles on so far. My stock speedometer is not working. I want to get the...
  7. dazwelding

    Brand New T56 Magnum XL rear seal pop out

    **I have the T56 Magnum, not the XL** I installed a new T56 Magnum in my 03 Cobra, and had issues with the bellhousing (see my other thread on that if you are interested). I took it to Pro-Dyno for them to figure out the issue in the bellhousing and to get the Cobra driving. They finished it...
  8. dazwelding

    Screaming sound in bell housing

    We just started our 03 Cobra for the first time in long time, and there is a screaming sound coming from my bell housing (or that is at least my best guess as to where it is coming from). It sounds to us like it is the starter stuck on, but that may or may not be it. We have a new McLeod SFI...
  9. dazwelding

    Driver Seat Motor removal

    I cannot imagine I am the first one looking to remove the electric motor from the driver seat to save weight in my 03 Cobra, does anyone has any comments? Do I need to locate a factory GT manual seat bracket and swap it out? I searched around a bit, and all I find is results on how to repair...
  10. dazwelding

    Low Fuel Pressure & will not start

    The engine turns over with only 10 psi fuel psi and will not start. The only code I am getting is P1000, which is the OBD drive cycle testing code since the battery was disconnected for so long. Any ideas on what is the issue? The car has been a project, and this is the first time we are...
  11. dazwelding

    Lost oil prime???

    We primed the oil pump and the engine in our 2003 Terminator with oil last weekend, filled the oil, turned the engine over, and had at least 10 psi while cranking for a few seconds. The battery was about dead, so we would only get a couple of seconds of crank, but I had oil pressure. Today (one...
  12. dazwelding

    Heat extraction hood recommendations

    Anyone have input on which tiger racing style heat extraction hood to go with for the 99-04 mustang? I am looking at the Griggs and the Chicane23 in fiberglass at this time. The Griggs is significantly less cost than the Chicane23, but I don’t shop by price alone when it comes to my mustangs...
  13. dazwelding

    Do the USB ports fry your iPhone?

    I just started plugging in my iPhone to the USB ports (both the one in the console box and near the shifter) to use the Apple car play features in the last 3 to 4 weeks. Since then my phone battery died and the front camera quit. The battery got to the point where it would go from 100% to dead...
  14. dazwelding

    New 18 GT

    Proud new owner of a 2018 GT A10 PP1 with Magnaride, Active Exhaust, and Recaros. Absolutely love this car. We will be setting this one up for drag. We have a 2003 Cobra we are setting up for open track, so it just made sense to pick up a GT with the new A10 for drag. Plus we had a ‘12...
  15. dazwelding

    WTT/WTS built AOD complete setup

    Built AOD transmission setup from a auto swapped 03 Cobra for trade for a complete T56 setup, or $3500 for all the parts listed below. This setup came in the car when I bought it, so I do not know everything about it. If you are interested in buying or trading and you would like more...
  16. dazwelding

    Tires: Drag Radials vs Stiff Wall Slicks

    I have done my research and I am down to my final decision between radials and stiff slicks. I have no class restrictions where I race, I will only be running in bracket classes. My car is NA with minor power adders. I will be purchasing skinnies for the front also. My only question is...
  17. dazwelding

    Tires

    I recommend Continental DWSs for all season tires for the Boss 302. I have ran them on a couple of Autocross races in the rain and even one with some snow. Our car did very well those days. I bought these tires to keep my family safe during inclement weather, and they are doing a great job...

Top