Search results

Hello all. I recently installed (300 miles) a calimer stage 3 MT82 and an RXT into my 2011. Break in is going fine, however taking off from dead stop and smoothly engaging from clutch to throttle makes the passenger rear wheel feel like it wants to jump off the car; it shakes and convulses so...

The time has come for me to part ways with my 5.0 I'm the only owner, and have loved it for the past eight and a half years, but it's time to move on. The car has just shy of 28,000 miles and I have the title in hand. I don't have current dyno numbers; the last time it hit the rollers it was...

Hi all, but of a wiring noob here. I've been trekking through a level 2 return system, and the wiring has me stumped currently. I spoke with Fore, but their instructions aren't helping me that much. I need an ELI5 explanation. I have an FC3 and a dual pump setup, and these are the instructions...

Acquired this from a buddy, and don't have the intent to install it. Asking $150 OBO Part is located in Columbus, GA

Acquired this from a buddy years ago, and never really had the interest to apply it. It's for the guy that wants to get the "BOSS" look to their mustang. I know the pic is bad, I can lay it out and take another if someone is interested. Asking $75 OBO Part is located in Columbus, GA

Springs have an estimated 20,000 miles on them. They show average wear, nothing excessive. I swapped them out in favor of BMR drag springs. Asking $100 OBO Springs are located in Columbus, GA

For sale are my original brembo package wheels. They have an estimated 20,000 miles on them. Never curbed, rashed or bent. There's a few stray marks, but no massive unsightly wear. I'm asking $300 OBO. Wheels are located in Columbus, GA.

These gears have a whopping 10,000 miles on them. I swapped them for a set of 3.31's after I added a whipple. I can remove the stock posi if need be.

Hello all, I'm planning to install a Fore level 2 kit, and I'm not having much luck with finding a decent installation write-up. I did find one thread here, but none of the pics are uploading and I could use some visual assistance.. Does anyone have some handy tech tips with pics they could...

Hello all. My google-fu has been less than helpful so far. I've long suspected I had an exhaust leak after my ARH headers were installed, and after dropping my k-member yesterday sure enough I found one. The drivers side top right bolt was loose, and after swapping gaskets I attempted to...

Hey all. I've extinguised my google-fu and am curious if anyone has some insight into this issue. This only happens when I take a fairly sharp turn at 40 mph or higher. What happens is the speedometer needle will actually zonk out and drop from my current speed down to zero and repeat. After...

Hi all. My father and I are performing a few more mods in March. I have 31 spline Strange axles (1/2" studs) with NO ABS Reluctors, gears, tru trac and diff cover waiting for me at home. One thing slightly confusing to me is not the fact that ABS Reluctors are not included with the axle, but...

And now, I'm here to learn more: Ok, so I've been building up my car for quite sometime now. For this day out I was using a 100 octane tune from Lund himself and it pulled like crazy. On 8 psi with 93 octane the car hit 612 rwhp, I'm on 10 psi so not really sure what the power is but it...

Hey guys. This is my first thread here after a fair amount of lurking. I recently joined the wise legion of boost converts with my 5.0, and even though my car is 2,000 miles away (or so) I'm still planning on ways to plant my power. I'm only at about 612 to the wheels right now, and before...

https://www.youtube.com/watch?v=h6pVULFArcg