Looking to buy a CJ Mani setup with a monoblade. Ported intake and a rev auto or PMAS CAI preffered. Shipped to 66757. Please PM me so that I can get an email notification.
Thanks!
Whats up everyone, just here for some advice.
Currently I have a FBO 2014 with a ported boss and an airaid. Someone local has an accufab TB I can buy. However I could also just sell my setup and use the money towards a used CJ if I can find one. (New price not feasibly) Would the accufab even...
I ma not be comparing apples to apples, but I can assure you that the GT350 will be much quicker around a road course or autox course. I have many similar suspension mods on my 2014 GT (k member, Control arms etc etc) and it still doesn't compete with a nearly stock 2015+ GT in an autocross...
Just wanted to leave a good review for Shaun at AED. He continues to surprise me time and time again. He responds withing a couple of hours every time and always answers questions I may have about future setups. I have had full bolt ons and his tune since 12k miles, now at 26k without any...
Well this weekend I tried my first autocross event. Car is a 14 GT non-Brembo with full bolt ons. Car was a handful, but my god did I have a blast!!! My goal for this fall was to cobra jet swap and attempt to go 10s NA. Well I think im going to sell my drag radials and go to more of the...
Hello All,
I was just wondering what everyone thinks the weak link in our diffs is? I have upper control arm/mount, lowers, did steeda sports and koni sports and somehow the car hooks harder than ever. Axle tubes are also welded.
Went to the track the other day expecting to go slower and to...
Hey Everyone,
Well I have been fighting a weird front right suspension noise on my car for the last 3k miles. At first it was a slight clunk when turning onto an inclined surface (IE driveway, store etc). Well last night I replaced my lower control arm and still the same thing. You can also...
Hey everyone,
I'll be taking the mustang from Kansas to Boca Raton Florida for Christmas and was wondering if it would be safe to run 91 or lesser fuel if I remove timing from with my SCT? The car is tuned on 93, but is not readily available around here (i keep 15 gallons extra at all times)...
http://www.roadandtrack.com/car-culture/a27194/road-track-2016-performance-car-of-the-year/
Awesome feat for ford. Cheapest car on the comparison by quite a bit. Apparently they did an amazing job with the overall balance of the car. Still wish the car could have been at least 300 lbs lighter...
Well, after speaking to the service adviser about the control arm creeky/noise tsb, he refused warranty work due to me having a tubular k member. (i spoke to him before letting him look at the car). Question is, is there any difference between the regular boss 302 vs gt control arm? I know the...
Well, my warranty claim was denied at ford for the replacement of the creaking control arm due to my tubular k member. I dont want to go to tubular A arms because I dont want any increase in NVH. I know the boss 302 control arms are an option, but have any tried to swap the bushings for the...
Well guys, lately I've been contemplating parting my car out and returning it to stock since everyone wants to low ball me and give me way less than NADA for my car.
I had planned on keeping it a long time, so I have done nothing but quality parts on it such as:
Kooks longtubes,
3 in x pipe...
About three month ago I began hearing a clunk somewhere on the car. At first it only happened when turning onto inclined driveway and occasionally taking off from a stop. It is not to the point where its popping every time i turn while the car is moving at low speeds/ hit larger bumps etc.
I...
First off, I apologize if this is in the wrong section. Not sure if the is simply a mustang general talk page.
Now to the point of this thread:
I have been a die hard Mustang fan ever since I was about 12-13 (now 25). My neighbors had two fox bodies, an LX 5.0 and a Capri. When I turned 16 my...
Now that GM has released its official 2016 Camaro #s, what do you think Ford will do in order to keep up? About the only category the Mustang will be better in is aesthetics. Im a die hard Mustang fan and hope that this pushes Ford for further development of the chassis and coyote engine...
Hey everyone,
I was just wondering what the average power was for people breaking axle shafts on these cars. I cant find any info on it besides people twisting axle tubes.
I plan on running my car in the next couple weeks and I am a full bolt on car (boss mani, long tubes, e85 etc).
Car is...
Well, its about time I start doing some more weight reduction, and I can think of an easier way than by swapping front seats. Whats the average weight savings?
Also post pics, I'd like something that looks like it could have came factory, and no, I dont want factory Recaro's.
Hey everyone, my car started making a popping noise when I take off or turn into a parking lot with any sort of incline. I first replaced my lower control arms to make sure it was not the spherical bearings and it was not. I did notice the right right sway bar link has just a tiny bit of play in...
Hey everyone, well if its not one thing, its another with the exhaust on this car. When the car was stock i purchased the 3" Borla atak catback that has resonators attached to the OTA pipes. Well the damn exhaust fit like crap, I always have to adjust it etc. Well now a rattle has started (very...
Hey everyone, my upper control arm/mount will be in Thursday and want to install it before the weekend. I tried a google search, along with a search on here and didnt really find a how to on anything but lower control arms, or just the upper arm w/o bracket.
Since room is an issue, can I just...
Hey everyone,
I need some advice on whether or not I should sell my car. Car is a DIB 2014 GT Premium. I dont really need to get rid of it, but it sure would be nice to free up some money as I pay about $740/month after insurance. My major problem is I owe 30k on the car still, and dont know if...
Hey everyone, I installed a JPC Clutch line last night and noticed that I had a leak at the fitting at the bellhousing. It is not leaking at the threads, but where the oring/fitting snaps in the elbow. The E-Clip is in all the way, and I still notice a little bubbling from the line. Anyone have...
Im finally to the point where im about ready to mod my car and get it tuned. Within the next week or two Id like to order a boss manifold, aluminum driveshaft, jlt CAI, and possibly a BMR tubular k member. Just seeing who could give me the best pricing on it all. Thanks!
Hey everyone, just a little background. I graduated college in May, and got offered an engineering position at a foundry. Ive only been with the foundry since August and it is privately owned so pressure/stress are pretty low with my position. The owner of the plant paid for my move down to...