Search results

Replaced both front abs sensors not long ago and everything was perfect up onto now. I have an intermittent abs light, no DTC codes (does abs report to obd2?). I pulled abs codes and got the following: 31, 33 and 63. Continuity fault left front & right front and voltage supply interruption. Any...

I have for sale a T56 harness for a 03/04 cobra. Asking $100 plus shipping.

I did a T56 in my 96 cobra and used the clutch fork and dust shield from my T45. I noticed it was rubbing and making noise. My question is are the clutch forks the same size or do I need a T56 clutch fork?

I have an older gen orange handle mgw for T45/T5. Asking $140 shipped.

Is the rear driveshaft yoke on a 99 cobra the same as an 03/04? Doing t56 install with an 99 irs and an 03 driveshaft

Is it better to use the t45 harness since it is the correct length or should I extend the wires on the t56 harness? If I use the t45 harness what all needs to be modified? I know the reverse will need extended. Does anyone have a diagram for the t45 harness?

Doing a T56 swap on my 96 Cobra with 01 IRS. Looking for an 03/04 driveshaft, let me know what you have.

Doing a t56 swap, do I need any additional adapter or polyurethane mount for it?

WTB: Stifflers crossmember for T56 into a SN95 WITH IRS 03/04 Cobra Driveshaft

Where can I find how to wire a speedcal? I already have one hooked up with my T45 (PO did it) but I am going to swap in a T56 and need to figure out how to wire it.

I am getting two codes P0351 & P0352, both ignition related. Any idea what is causing it?

Looking at doing a t56 swap, I have mostly stock 4.6 and a 01 IRS w/ 3.55. My question is, will my car drive like poo with the gear ratio of the t56 with my setup?

Looking for some advice/setups to get rid of swirl marks and prevent them on my all black car. What kind of buffing setups should I look at getting into and what can I use to remove the marks?

So I am weighing my different options on rebuilding my motor, can you guess give me some insight and opinions? As most are, this is aiming at a budget build (i know, nothing is cheap with these motors) 1: Buy used block, freshen it up (bore, deck etc), new rods/pistons - get them balanced with...

Looking for opinions on MM Solid Steering Rack & Aluminum Steering Rack Bushings. I want to tighten up my steering wheel and get rid of some play. Will these eliminate it?

Any one have or know where to get the wiring diagram for GT seats?

I just picked up a set of cloth 2015 Mustang GT Seats (both electric) to swap into my 96 Cobra. Here is where I will document the process of installing them. Plans: Replace carpet & double din install Reupholstered later on down the road to black leather w/ green "SVT" Possibly selling rear...

Odd request, can anyone get the thickness of the engine harness on both sides? Need a measurement for new loom wrapping

Looking to buy a rebuildable t56, let me know what you got.

Looking to buy the following: Moroso coolant tank Moroso power steering tank Let me know what you have!

I am looking to buy an upper intake lid only, I plan to do an egr delete on it. Please let me know what you have!

My car has come a long way and I am ALMOST there! (but will I ever say I am done perfecting it?) The day I brought it home COP Conversion commenced Powdercoat everything Who needs emissions? Lots of hand painted pieces No more rusty coolant pipes Moar air Moar green! Moar...

I just trade my IRS Magnapack Catback (pieced together) for a IRS Borla Atak Catback. I have BBK Longtubes & matching O/R X on the car but I am looking for some sounds clips if anyone has any of ataks on a 96-98.

I am all about the little details and I love to customize everything on my car. Let me know what you guys think of my latest additions :D Custom Center Caps, Shift ball, Door Sills, and Rad Support Cover Before wet sanding

I rented a compression test tool today and ran the test, I did the following: Disconnected the fuel cutoff button in the trunk Removed all spark plugs Tested each cylinder one by one by holding the throttle to the floor and letting it crank 6-7 times. Here are my results: 4 - 110 8 - 130 3...