Search results

I disconnected fuel vent tube this Sunday and it took fuel so now I need to figure out what's going on with the tube I appreciate the help. Do you have any recommendations on what you would do?

Hi, I'm out of ideas on why my car isn't taking gas, so when I'm fueling up the car the gas pump handle keeps turning off as if the car is full. I have tried filling it up with the hand upside down and I have had no luck with trying it. I have changed out the vapor purge valve and vapor...

Hi, I just installed N2MB and spark plugs, and now I’m frequently getting flashing check engine light. When the flashing light comes on which the car starts to act up and feels and sounds like the car is miss firing, and this lasts for about 30-45 seconds before everything returns to normal. I...

Hi, I have been on how to install water temp gauge, and can’t seem to find where to install sensor. Could some one tell me where to install the sensor at and what I will need.

Wonder why the web site doesn’t say out of stock you can try MMR unless there site is wrong to, but it is a little more expensive. If this block is really hard to get I guess I only have one option for my self.

There you go if you’re really looking for one didn’t think they where hard to get https://www.cjponyparts.com/ford-racing-cylinder-block-aluminum-performance-tivct-4v-5-0l/p/M6010M50R/?year=2014

2011 with MT82

Sorry not sure how it got added twice, can a administrator delete this thread?

Hey Everyone, . I'm looking to build a short block that can handle up to 1200 whp for a supercharger setup, and need help deciding on these two block options. If you have any other suggestions I would love to hear it, also I live in alaska so it's hard to come by used block or get stuff shipped...

Hey Everyone, . I'm looking to build a short block that can handle up to 1200 whp for a supercharger setup, and need help deciding on these two block options. If you have any other suggestions I would love to hear it, also I live in alaska so it's hard to come by used block or get stuff shipped...

What should my pinion angle be for my UCA adjustable rod end?

I plan on running same model tire front and back, but my tires on the front are still have some life left and the tires on the back need to be replaced really soon. I'm looking to replace them first, and when I get little bit more money I'll change out the front to match the rear. Really isn't...

Thanks for the reply. This is all I was able to find near 285/40/18 online. Which one of these tires would you got with? 285/35-18 MICHELIN PILOT SUPER SPORT XL 101Y BSW 285/30-18 BRIDGESTONE POTENZA RE-11 97W BSW Also I'm running 255/45/18 up front will the Aspect Ratio on the tires I...

Hi Okay so I'm looking to replace my NT555 that I have on my rear, and I'm ready to try a new tire. I'm looking for a tire that has good grip to help keep the car to the ground, but also is decent in rain during regular driving. I would also like to find a tire that is built for street, and...

Thanks for the reply I just replaced my fan assembly two months ago with upgraded gt500 assembly, so is there a way to test resistor? I also tested the fan by starting my car and places climate control to max, and blower motor switch in the hi position. The fan turned on, but after a couple...

Hey Everyone I have searched the forums and couldn't find anything. OK so on my third radiator fan which is now dead, and I'm not sure what is causing them to go out. I did find the connector that connects to the fan to be bad, but have no idea what caused it to go bad. The connector was not...

Thanks for the info!

Awesome thanks for the help!

Can I reuse upper strut mount nut or do I have to replace it? Also what hole do I use on my LCA relocation bracket for my LCA?

Thanks for the help.

I'm looking to go with BMR Adjustable Rear Upper Control Arm - Poly Bushing, with BMR Rear Upper Control Arm Mount. For the rear sway bar BMR Adjustable Rear Sway Bar w/ Fabricated End Links - Hammertone. I'm to build the car for corners, but wouldn't mind taking her out to the 1/4 mile once in...

Thanks for your input, and it was lot good info to keep in mind.

Hi I am ready to start working on my suspension for my car, and I already have BMR non adjustable lower control arms, and BMR lower control arm relocation bracket. I use my car for a daily driver, and I also want to set up my car suspension for circuit track fun. Plus I also want to help my car...

Does anyone know what might cause a cooling fan to burn out?