Have front and rears 13k on them before took them off. Like new will post pictures tomorrow they are in storage. Great brakes plus let you run 17's up front if you want to track car. The rears I believe are the same as base so no need to do but if you want them you can have them just pay for...
Have front and rears 13k on them before took them off. Like new will post pictures tomorrow they are in storage. Great brakes plus let you run 17's up front if you want to track car. The rears I believe are the same as base so no need to do but if you want them you can have them just pay for...
Front and rear brembo springs
Front brembo struts and rear brembo shocks
1 factory brembo strut mount the other lost bearings during disassembly new one is $32.91 from tasca.
Brembo Panhard rod bar.
4 brembo bumpstops
Willing to ship or pick up local Northern NJ. All parts have about 1500...
I have one NIB brembo wheel bought for curbrash never used it sitting in attic $125 Shipped continental USA. Great if you rashed one or use for full size spair.
Have like new less than 100 miles on cat back part and about 1500 miles on headers, cat section. Willing to ship or local pickup NJ for a great deal! There in my attic no pictures but like brand new!
FS Price lowered 2013 Mustang GT Premium Black , Brembo, Paxton, MT, Magnum Xl
2013 Mustang GT premium with brembo package and shaker 500 sound system
Modification list:
Power adders:
Paxton 2200sl polished with
Beefcake Tq booster i.e. waste gate pullied down to 3.33 with gates belt and tial...
Tires have about 70% tread left MT DR 2's 275/60/15. Wheels are Jegs Drag II 15x8 direct fit. Good bite just went to Nitto's on my RTR wheels instead. Good deal I think New like $750 . I used them on manual transmission walked out of the hole still cut 1.6-1.8 60 foot times perfect for auto...
Ok I have DR now 15x8 275 60 MT streets car can cut 1.9 60 ft time but walking out the hole I have a spec twin disc clutch with aluminum flywheel which makes it like a light switch on launch really tough to walk out. So I'm thinking 17inch wheel with hosier 28x10x17 slick. I want to keep my...
LCA and Brackets are in good condition with 5k on them will sell as a set $225 shipped lower 48 states. These brackets worked really well eliminated all of my wheel hop! Depending on power I would start with these 1st and leave UCA stock under 500 hp for manual. I went FI did whiteline UCA...
So I'm switching out my metco billet LCA's with there relocation brackets to adjustable whiteline and there relocation brackets. Jacked the car up by pumpkin and put jack stands under the axles and started with passenger side doing only one side at a time. I had the jackstand to close to the one...
Looking to sell koni yellow struts assembled with Gt500 mounts, bmr front springs, dust boot, and spring isolaters also included is rear koni yellow shocks bmr springs and pre cut factory bumps stops unbolt your stock stuff and bolt in. No spring compressor required job can be done in under two...
I have factory 3.73 gears with 2500 miles on them no whine from my 2013 gt brembo. Then I have ford racing 3.31 with 6000 miles on them no whine or noise either. I went tremec magnum and went with 4.10 . I'll do $75 shipped continental US each. Check my seller rating I'm fast shipper and items...
So I had a tremec conversion installed with spec twin disc clutch, JPC clutch line and the 1st time I picked up the car the clutch would make a noise during the last inch of pedal engagement. I chalked it up to twin disc and the plates rattling but after 500 miles driving 300 of highway and 150...
I would like to know what the numbers are and what is ability to change it on stock setup, cammed setups, etc. I'm going to do some of my own calculations and searched on here but didn't find any info.
FS 2013 MT-82 8500 miles, in NJ $700
Trans is working fine went to Magnum. Shifts like new changed original oil at 4000 miles replaced with Ford $25 dollar a quart stuff. $700 will meet in Tri state area. Located in NW NJ. Need it gone! Willing to ship as well
[/URL][/IMG]
Ok I have noticed if I run my paxton setup on the highway for two gears like 3 to 4th temp goes to the al of normal what is the corresponding oil temp in that range since there is not Fahrenheit out put for temp. Guess its time for boss oil cooler.
Ok I have 2013 with paxton via beefcake and finishline tunning, install and purchase was great experience. Terry and Brian are great guys and an awesome combo vendor and installer wouldn't hesitate to recommend. Now with Lund they did my dyno tune and I was tuned by Shaun/AED before and had...
How long or how many miles does it take the computer to learn to get an accurate datalog? Reason being I'm using a fuel additive ACESIV that raises octane from 93 to 101-102 octane. So what I'm trying to accomplish is do a reset fill up with additive let computer learn the long term trims than...
Selling couple of things since I went FI don't need them anymore
Factory 3.73 gears 3000 miles on them no whine switched to 3.31 since FI $100 shipped
47lb FRRP injectors have about 2000 miles on them went to ID 1000's great for NA who want to run e85 $175 shipped
I'm in NJ if anybody...
Ok here it goes back in April when beef and I think JPC or BBR were having a pissing contest who can sell a kit for less I got in on the $4288 special installed! Well fast forward to last week my kit was installed by Brian at finishline with the help of Terry doing some logistics like extra...