Search results

ok SO.... I just intalled a 3/8" intake spacer from PHP and had the battery disconnected. when I was done and fired up the car it idles really rough almost sounds cammed. I have checked all the connections to make sure they are good. Any thoughts? Please help ASAP this is my daily driver.

Hey all, As of late my mach has begun a transformation. It now sports a JLT RAI, MAC off-road H-pipe, Flowmaster 40 series weld-ins, SR lowering springs, KYB shocks/struts and anthracite FR500 17x9/10 with a 315/35/17 on the rear. I just ordered my custom tunes today and can't wait to put them...

Hey all, Recently as in today, my car has developed a clicking noise when I turn the steering wheel from 12 O'clock to about 10-11 O'clock position. It only does it going to the left. I can feel it in the steering wheel and in the floor boards. I know for a fact that it is from left. My car...

Hey guys, I have a question or two and need some insight and opinions. First my car is an 04 mach 1 with a JLT RAI and Flowmaster 40 weld-ins. Will a BBK O/R X-pipe or a mac pro chamber bolt up to my existing stock exhaust since the stock exhaust diameter is 2.25"? Second Which should I go with...

Just feeling out if anyone would be down to meet up and cruise maybe up to mount lemmon or some place in about a month or so.

Hey guys, So I have started my agonizingly slow build on the Mach. So far I have done a JLT RAI and had flowmaster 40 weld-ins installed. First question, can I run long tubes and a catted mid-pipe with my stock 2.25" exhaust piping or do I need to eventually get a cat-back? I know most...

Anyone know anything about a mustang club in Tucson? I know about southwest mustang club but my understanding is they are more of the purist time instead of the performance type and I believe they might be older individuals, correct me if I am wrong. I also know about the vail mustang club and I...

Hey all, Is there a reputable shop to install cams and/or dyno my mach in either the Tucson or Phoenix area? I'm looking for personal experience or suggestions. Thanks! also pricing would be helpful. -Tim

Hey guys, my next mod on my car will be lowering springs along with shocks and struts. I'm looking at a kit from latemodelrestoration.com that has KYB shocks/struts and SVE lowering springs. Anyone know how much this will lower my mach? The site says .75"-1.25" depending on model and engine. The...

My Mach is 8 years old with 94K on the clock and I have began to notice some things. First the suspension is real rough, when I hit bumps I hear a external rattle from the passenger side. Next when I have the A/C on I am getting an annoying squeaking sound from the dash and it appears to be the...

Does anyone know if MAC long tube headers will mate up with a BBK shorty catted X-Pipe mated to SLP LM2's. I am trying to decide which setup to go with. I could run BBK LT's with a BBK X-pipe but the MAC's are said to be just as good as BBK for cheaper. Thanks -Tim

I'm not sure where to post this on the forums but here it goes. I'm looking to install a set of Comp Cams XE262AH-114 (106100) on my mach one and just curious what "stage" cams these are? Also is anyone running cams on a N/A daily driver with 4.10 gears or stock gears? If so what is your MPG...

Hi All, I'm relatively new to DOHC 4.6L engines but not new to mustangs. I have an 04 Mach 1 Manual and I have a few questions that hopefully I can get the answers to. For starters my goal with this car is to be as close to 400RWHP as possible and as close to 11 Sec 1/4 ET's as possible. I...