Picked up a lund gauge, selling my used PBD ngauge. I dont know how to get it unlocked, but it can still scan your car for any info your OBD2 puts out, and can be used for data logging. Can watch up to 6 gauges at once. comes with window mount and OBD cord.
Asking $500 obo shipped
Hey guys,
So car is an 07, buikt everything. last summer i bought a set of bullet blower cams to swap out. Pulled the motor, and found one journal had a bit of galling on one journal, driver side, intake, #3 cap. I smoothed it out, then continued the install and degree.
After the install, on...
Went turbo, so selling my Whipple super elliptical. Its in great shape and comes with the adapter plate and paper gasket for the plate. Flows 2750cfm, which i believe is the biggest and best on the market.
$600 shipped + pp fees
2zero6-852-zero158
Went TT and going to have PBD do the tune, so no longer need my Lund Ngauge. Selling with brand new cord, SD card, and adapter cup. Works great and is an awesome addition to any GT500.
$400 shipped + pp fees.
You can reach me at 2zero6-852-zero158
Thia thread is about the quest for shorty headers.
So, after much dismay and difficulties with my FRPP shorty header fitment, i splurged and picked up some of the ceramic JBA shorty headers. JBA is the only other company that put out shorty headers for these cars that i know of.
Well, i just...
Selling a set of Ford Racing Performance Parts GT500 shorty headers. These have been profeasionally ceramic coated. They connect to the factory x pipe. Mocked up on my car for a turbo system, but never used. I also used my die grinder to clean up some of the flange to runner welds that ford...
Hey guys,
So i just got the motor back into the car. I noticed the passenger side FRPP header comes out so far it was over the K member bolt holes, so i left it off and dropped the frame back onto the k. Got everything tightened up, and moved onto the passenger header.
So i moved AC and...
Going turbo, so selling my exhaust! I have a kooks Boss 302 style O/R H pipe that i had on my 07 GT500. The exhaust is factory hookup to over axle pipes on any 2011+ GT500. (2.75" oem exhaust clamps)
If side exhaust doesn't interest you, block off the flanges and you've got a normal GT500 3"...
Picked up a set to run in my car but decided to go a different route.
CAMS SOLD + pp to the lower 48
Also have bnib ARP 2000 bolts for these cams.
$ BOLTS SOLD
2o6-852-o158
Selling the MMR billet secondary chain tensioner correction kit with ARP hardware. From factory ford tensions on the wrong side. MMR says....
"ALL (Ford) DOHC's tension the chain on the wrong side, this creates cam timing errors as great as 7 degrees (regardless of how the cams are degreed!)...
Going turbo and swapping cams, so selling my big SC cams. Cams require springs and retainers, not included.
Set of MMR stage 3 supercharger cams. These are 244* with .495 lift, both intake and exhaust. These sound very lumpy. They have about 6000 miles on them.
SOLD the MMR
SOLD the bullets
Going turbo, so selling my exhaust! I have a kooks Boss 302 O/R H pipe with QTP electronic cutouts and wiring. The exhaust has factory hookups for 2.75" oem exhaust clamps.
Asking $480 + ship and pp fees for H pipe
QTP cutouts SOLD
Thanks! 2o6-852o158
Turbo time, so parting ways with my kooks LT's. Ive installed alot of headers on these cars, and these are the highest quality headers you can buy for GT500. This set was advertised at 2011+, but i had them on my 2007. Not sure what would make them for later models vs early? I ran an EGR block...
Selling my Thump billet tensioner and 90mm idler. Idler is missing a little bit of the black on one edge from rubbing on my intercooler line port. No issues, just had to loosen and tip it up
Thump is SOLD
$30 shipped and pp fees for the BPS 90mm idler
2o6-852-o158
So...I'm doing a TT hellion kit with sheet metal intake on my 07 GT500. Im leaving the AC for my KC, so I need to figure out how to route the old SC belt so it will still spin my AC compressor. Anyone have pictures or can give me a detailed idea of how its ran?
Thanks!
Selling my REAL carbon fiber JLT 155mm intake. I dont think JLT makes these anymore. Comes with a heat shield for 07-09, i may have a spare 10+ in my shop i can swap it out for. Will come with silicon coupler shown for KB big gun/whipple super elliptical oversized throttle bodies.
$450 shipped...
Bought a turbo kit. So its time to sell my whipple 4.5L supercharger. It has about 2500 miles on it, and will come with a 4.5" pulley that makes 18-19lbs with cams/LT's/ported heads/ATI stock lower. I will also include a smaller pulley for 24lbs. Comes with newer belt, less than 100 miles, and...