Search results

for sale: Holley NOS plate kit with 2 10 lb bottles, all the lines needed to hook it up, 3 sets of jets, automatic bottle heater, purge, and n2mb wot box window switch. Asking $600 shipped to you

As the title states I have these four things for sale and all but the rear end braces are in good used working order. The rear end braces are brand new never installed UPR units. I have pictures of all of it and all prices are best offer takes it. This is my first time posting for sale on here...

Curious what people are running successfully on the front of their lowered cars? Im up for opinions from people who are in a similar position. I was looking for a 185/55/17 and see that is a hair over 25 in. tall. I can only run a max of 26 in tall tire on the front. The car will be mainly for...

I dont know what to do with these axles and I do not want to throw them away if I dont have to. They are a 1/4 in. too short for my 99 Mustang GT rear end. I actually used them for a short time by putting washers on the back side of the rotors so they would not rub on the caliper. So its not...

I need to get my car unflooded. Heres what I know; there was raw fuel coming out of my JLT cai and the oil is saturated with gas. I have a fresh oil change ready and a new set of plugs. Im sure the cylinders have gas in them as well. Im just looking for a proper method of getting the problem...

So, this is my experience with the pprv delete: So far I have dropped the tank 4 times now because of one of the hoses blowing off and here is why, I think; Two of the times ( after cranking the engine over for ever due to the fuel flowing back to the pump because there is no pprv) the idle...

Fresh tune from a Mustang Guru out of Detroit, car runs phenominal and now my pumps go out! My experience has taught me that perhaps BAPs are not the answer when trying to address fuel needs when modifying cars. My pumps lasted a total of 8 mos. with the BAP wired 100% all the time ( not boost...

I have a cobra converted to solid axle 8.8 housing. I chipped and axle where the c-clip goes and I replaced with moser hardened axles. When I called them to order I must have given them the wrong measurement. Is there anything I can do to remedy the back of the rotor scraping the the caliper...

I have a 03 cobra that was just tuned and I am trying to eliminate problems before I find a new guy to tune it! First off, I noticed something was not right as soon as I left but did not notice the stumble at idle or cruising speed until next time out driving the car. My problem: noticeable miss...

03 cobra running meth and I just bought the n2mb wot box. I read that they sell and recommend the nitrous/meth window switch. I am curious if I am able to run the meth without the window switch? Reason being, I have the meth hooked up to run based on the maf reading. It would be great if someone...

WTB a 40A Kenne Bell Boost A Pump.

I have an 03 cobra with a ported Eaton. I put down 491whp before I put a cai and a large oval TB. I expect over 500whp now. My question is how much boost could I run safely with this eaton? It was tuned with 14lbs on only a upper 2.7 pulley. Do I dare drop one more pulley size? I plan on hitting...

I just got the cobra mustang dynoed lastnight and i was actually quite surprised. For only having a 3" upper pulley, cai kit, custom 3" exhaust w/ high flow cats she made 429.5 hp@5700 and 459.1ftlb@ 4000 . The guy that dynoed it said it had to have been tuned like this and i wanted to see what...

Hello to all, I am from Michigan and I just bought a 03 cobra. Its pullied ,full length headers, ca kit, custom 3in exhaust, etc. Screamin yellow! The first question I am hoping to get help with is a rather simple one. I have an annoying squeaking noise coming from the passenger rear tire. the...