I don't know if folks still do it, but figure I'll ask: Would anybody near or south of DFW take a look at a truck for me? Lancaster to be specific. I can venmo/PayPal/Cash App for your troubles.
My question is will the Saleen style hood with heat extractors clear the intake? Specifically, I'm looking at the TruFiber A70 SLN. I was trying to shy away from using the '00R hood if I could so as not to be a poser yet still have something functional.
T56 26-spline mating up to my 5.8 "R". Mostly street and strip use. Highly doubt it will ever see much other than a 1320 a few times. Shooting for 500hp/450tq. Any suggestions for clutch, flywheel, etc?
Posted in the R section to limit the "what a stupid question" or "call your tuner" or any...
SOLD!
Selling because trying to downsize a little (4 cars), and be an adult (buy a house instead of renting)....until an electric mustang comes out. Then I'll be in debt again. Some pictures are dirty. She needs a bath. She cleans up nice, i promise. Better pictures coming. Just trying to get...
Anybody know or have a clue if this will clear the upper on an R? I'm a poser and have an AJE k-member and am shoving it into a GT body.
Sent from my HD1905 using the svtperformance.com mobile app
Looking for a no or low drone quad tip, if that exists. If not, then single tip it is. Acquired a '14 GT with Flowmaster Outlaws and at highway speeds it's unbearable. I'm not old, but it's ridiculous. I've had full exhaust setups before and this is by far the worst.
So, looking for...
So, based off what I've read it kinda sounds like pinion angle or maybe something driveshaft related....but i'm hearing this whine/almost beeping sound above 55mph. And it only seems to be speed dependent. It does it regardless of engine RPM, gear, load, and clutch engagment. I'm fairly familiar...
Hey guys/gals - Those of you who've had Bob tune your car, did he have a preference of fuel injectors and pumps? I guess it doesn't matter too much, but I'd rather make his life easier if he has a preference or has a certain way he does things. And I know he's usually pretty busy. Thanks.
I'm swapping a 4v into my '03 GT. From what I've read, the best bet is a 4v wiring harness for the injectors, etc, a 4v computer, and the rest of my 2v wiring should suffice. But, I know there are issues with PATS. So, is there a particular computer that's better than the others that is tuner...
Alright, I'm trying to get myself into a new-to-me coyote. What issues/problems/quirks/etc should I look for to scrutinize over when looking this thing over.
Anybody running Eibach Sportline springs (red ones) that can take some actual measurements for me? Looking for a measurement from the ground (preferably on a flat surface) to the underside of the fender? Need them for front and rear. Preferably millimeters. Thanks in advance.
Had a shop install my coilover kit. They didn't use the instructions, uninstalled my MM cc plates, reinstalled stock cc plates. I've reinstalled the MM plates now. But they mixed and matched stock and SR coilover kit parts and I don't know what does and what does not go with the kit. I have AM's...
Has anyone completed a 5.4 build w/ C heads and a Coyote intake(using the adapter plates)? If yes, what were your dyno numbers? I'm interested in building one for my DD. Nothing crazy. Just something fun back and forth to work and that can get out of its own way. I've seen the 5.4 builds with...
As stated in the subject line, what is the color of the Recaro seats for the '00R? I'm going to buy some straight from Recaro but wasn't sure what the actual color was. They look grey-ish in pictures that I've seen, but wanted to verify. There apparently is an option for black too and several...
I want to port/polish my R lower but don't want to put in the hands of any ole person. Can any one recommend someone (in the southeast preferably...I'm in SC) that they have had a good experience with in regards to this?
So, I re-started my project car. Was going to try to get it up and running...but, before i even popped the hood, i encountered the awesomeness that is grey mold. It's on everything (seats, door panels, carpet,etc). The car's been sitting outside for about 3 years now. Any advice on how to get it...
Thinking about getting rid of it. Only had her for a small while but it's really more than I need. Would consider trade for a nice 03/04 Mach 1(would prefer Comp Orange, DSG, Azure Blueor Black) plus cash to me or a turnkey 5.4 swap car.
2008 Jeep SRT8 - Black
-Heated front and rear seats...
Up for sale is a mostly stock 2002 SVT Focus - 3 Door. No trades. $6,000 obo. Make me an offer. Motivated to sell. Title is free, clear, and in hand. Located in 29829 - Graniteville, SC
Questions/Offers/etc: [email protected] or PM me.
All pics...
Some of you may remember I'm building a 5.8 R motor. I've seen that most use the stock 90mm that comes with the engine. Would there be any benefit in stepping up to the 100mm tb that Dragon offers? I know the Dragon is mostly for boosted applications. I guess I'm curious is to whether anyone has...
I'm pretty sure I already know the answer, but I'll ask anyway...Do I need a 4V computer for my 4V swap or will my 2V computer work? I feel like there's something inherently different between the 2V and 4V computers that would make them not interchangeable...
Anybody know?