Search results

  1. T

    Header + short run exhaust combos?

    Anyone know of any ?
  2. T

    SCT X3, used once!

    Paid 380 + 150 for the tunes... + shipping. 280 shipped! Paypal only, add 3%, USA only.
  3. T

    DIY blower port

    I cant seem to turn up any with search, but i KNOW someones done it!! All that is done by the shops who charge for it is some material removal in the compressed air side right? I've seen the pictures, doesnt look that hard.. is there any reason i shouldnt try it?
  4. T

    Rebuild time

    I scuffed a piston & am doing a bottom end rebuild, I'm going to reuse my rods and most likely the bearings etc.. it was pretty minor damage, but enough to make a slight tick so i took a look 'n found some uglyness (dont seem to have the pictures of the piston, i thougth i did.. i'll post em...
  5. T

    What do you do when your with out your cobra?

    say, on a vacation? http://www.putfile.com/media.php?n=RentalVan9
  6. T

    Putting on the stock pulley, can it be done?

    Search is fuxored.. I tryed :( I have the need to stick my stock pulley back on ( got a tick in the head & want to try to get it fixed via warenty) gonna need at LEAST to dechip & pulley the car,.. if it CAN be done whats involved? (i've got a pretty extensive ship, but i'm afraid of sticking...
  7. T

    Ticking near cyl 8.. wtf? wrong side??

    I ran some 90 octane with a chip tuned for 92, detonated & blew 3 plugs up (all on the right half of the engine) on the way to the track.. switched the plugs out for new ones, plut 4 gallons of 104 into a 1/4 tank of 90 oct & ran down the track a few times (got real crappy times out of it)...
  8. T

    Rear end paranoia

    finaly went for the pully, after listening to broke7 repeatedly tell me "no one cares how fast you run on a stock pully, they wont remeber you for high 11's or low 12's" I finaly tossed on a pully and chip, had a good day at the track pulled a 1.69, 1.66 and a 1.63 60 fts (but couldnt find...
  9. T

    295/35/18's on 18x9 rims,, can it be done????

    I've heard yes a lot, but ive given it to two different shops and they say that tire size wont fit on these rims i even tryed to help on one, the first bead went on fine, but the 2nd one wouldnt fit in, we even stood on the tires to try and get the bead to go in is there a trick to this...
  10. T

    good air/track prep,... bad clutch? wtf

    the MPH is there for 11's but the 60ft isnt, anyone have an idea of whats going on? I'd really like to tap 11's with as little mods as posible right now ive got clutch quadrant, short shifter, JLT CIA, no mufflers (stock pipes and cats though) everything else totaly stock, running...
  11. T

    Rims, looks, size (ya its all been done before)

    18x9 + BFGoodrich g-Force T/A KD 295/35/18 + = work? I'm pretty sure the sizes will work, hell people are squeezing 335's on there and 315 seems most common, but when exactly do you start worrying about irs bolts? it seemslike its different for everyones car (rim size...
  12. T

    quick runs for stock(or very close to stock) cars

    what's some fast runs for low low mod cars? I have a JLT CAI and put some ET streets on 12.297 @ 111.37 it felt really good, but I just couldn't get my 60 below 1.8xx
  13. T

    New cobra, things to check on?

    Picked up a '03 Cobra from a bank (REPO'd lol) I know some of the history front brakes were toast (front right calipur(sp) locked up and broke off the mount, so the entire front brake set up was replaced, Rear rotor's were turned too, really ugly job of it,, guess dealerships dont worry much...
  14. T

    Hello

    Just invading your board.. <- Evo owner, who likes more than "just the strait line" :lol:

Top