- 12 6 oz cans of Enviro-Safe Industrial R134a Replacement Refrigerant. $65 plus shipping
- New pilot bearing $7
- Duda energy 1" T valve 2x 1” to 3/4” with brass adapters and 2x 3/4” brass fittings. This is used to switch between a Killer Chiller and H/E if you want to be able to isolate each...
I prefer not to ship but if you make arrangements I will load it on a pallet and drop it off.
Check out the video I made showing it working in my car before i pulled it.
**The video has my SVT_Troy proof in it**
T56 out of my 03 cobra with 10k miles since rebuild years ago.
Comes with:
*...
- Mechman billet 240amp alternator $325 shipped plus PP fees
Comes with the upgraded 3rd wire (taps into a 12v source) ready to plug in so you don’t get a flickering battery light. It has plenty of wire to route it through the brake booster firewall grommet to the under dash fuse block via...
I just wanted to post a basic how-to on how I installed push-button latches. There are a ton of counterfeit/cheapo off brand products, I chose to stay away from them and order the real stuff.
Pointers I have after installing them.
1. remove the inner fender liners, if you have a CAI, remove the...
It came used with a tank I bought for sale. This is the re-programmed 25GPM EMP pump. Tested and verified the flow myself. It actually flowed 27GPM with no restrictions! It comes with the pump, harness and instructions.
SOLD
IMG_8439
I currently have H&R race springs (new upper & lower poly isos installed) with my DA rear shocks.
According to Vikings instructions they recommend softer compression for the street than they do for drag racing. Don't quite understand that one.
Here is what Viking's recommends in their...
For those that are/have run oil filter relocation setups what do you recommend?
I'm just looking for options other than the MM kit incase I go with a MM K-member.
Troy
IMG_7961
Full Tilt Boogie Racing SN-95 13" IRS Rear 2 piece Brake
Conversion Kit FT 7000A $SOLD
IMG_7783
IMG_6532
Russell rear IRS steel braided brake lines Complete with all hardware needed to install $SOLD
IMG_9309
SN-95 Brake Cooling Duct Kit (Don't remember brand but comes with new SS...
A friend of mine is looking for a Demon without silly dealership markup. Can one be found at MSRP?
Anyone have any leads to one? He is located in Ga around Savannah.
Troy
I'm looking to buy a pair of good/like new condition ipads for my daughters.
I'm looking at the following models in wifi only:
Ipad Air 2
Ipad mini 4
Ipad Pro 9.7"
Let me know what you have.
Troy
I'm running a 13/14 GT500 oil pan gasket and modified pan in my 03 cobra. I believe I have a leak with the gasket. I was planning on removing the pan to inspect everything. Its a rubber O-ring but do you guys typically replace this gasket when the pan is removed or reuse it? Whether I replace it...
I’m looking to buy both true forged intercooler and expansion tank. I prefer them to be unfinished making it easier to modify and re-finish.
Let me know what you have.
Sent from my iPhone using the svtperformance.com mobile app
I am getting ready to order a Steeda K-member I want to swap out the struts to freshen up the front end. I've been toying around with going to a coilover setup in the front. I am currently running Viking DA with H&R race springs in the back. my car is primarily a street car but i have been...
What is causing my TQ to roll over around 4500rpm versus staying flat like most S/C'd vehicles?
I recently had my car re-tuned after changing over to a return system. I have not had this engine/blower setup on the dyno prior for comparison. The car runs wonderfully, infact if i hadn't decided...
Its been along time since I've put my motor together with the help of Russ and Ed a few years ago. It's been running for awhile and has seen a few trips to the drag strip running decent minus it having a crappy driver. Breaking stuff trying to launch on MT ET street radials set things back even...
I have two issues.
Issues #1: Fuel Pressure (Pressure drop across fuel injectors in tune does not increase with boost)
Right now i am experiencing a extreme lean condition that starts off fat then back lean. I'm not the best with data logs but am learning. I trust my tuner and he says it is...
I went full return so selling off my old fuel system.
- Fore Fuel hat with dual GT pumps, 8AN feed fitting and new stainless bolts to install $SOLD
- -8 to OEM fuel rail adapter $SOLD
- Summit Racing 10 Micron fuel Filter 8AN on both sides (pn: SUM-230116) (used filter aprox 2.5K) $SOLD
-...
Thump RRR Tensioner PM-1003-76 (76mm pulley) $315 shipped
Bearing spins perfectly and no significant damage to the tensioner whatsoever. Clean and ready to bolt on.
Its been awhile and i have not stopped modding my cobra, I just haven't kept up with posting. Ive been lurking for the past 2 years or so.....
Anyway on to the pics
Added a Stifflers solid trans mount to clean up some sloppy shifting. I think it make a difference and my shifts felt alot more...
WTB 03-04 Cobra VMP TVS GT500 inlet/elbow and Throttle Body.
I currently have an accufab Tb setup, if your looking to trade with cash given on my end for whatever reason let me know
Sent from my iPhone using the svtperformance.com mobile app