Search results

I want to send my supercharger off for a port before it gets too much hotter. Anyone got any tips or gotchas for the process of removing that assembly? I've scoured youtube, but all I ever see is high speed versions of the process. Obviously there are some electrical connectors on the back...

I did a search in both GT500 sections and I don't see any threads regarding the installation of new 3.0 Whipple on a GT500. I'm kicking around either going to a 3R and this popped up on my radar, but I don't see much information about it, so I'm calling you out if you've done it. What I've...

I've doing some research on this mod and I've been unable to see any pics of how the hose ends are supposed to snake around the belts and idlers. If you have pics, please post them. Otherwise, please tell me what you did to make it work. J2 has this pic on their website, but I can't tell if...

The powder coating on the valve covers is flaking, so I'm looking for a set I could get powder coated. If you've got a set in good shape, I may take those if the price is right.

I attempted to hook up my Lockpick this past weekend, but as of now I have a question for those of you that have done this successfully. On some install threads I see they used the supplied GPS antenna splice for the lockpick, which Coastal says is optional. On other threads there is no...

After Tob began his thread about installing the 13-14 Pierburg intercooler pump in an earlier model in this thread, I’ve been slowing working toward making this one of the mods for my 2012. This write-up is a compilation what I did, my findings regarding the factory intercooler system and what...

While I've seen a few write ups on these, I can't say I've ever seen where people are putting the module. Do you locate it behind the radio, or does it remain inside the confines of the console?

I'm coming to the realization that my original battery is almost 7 years old. While I do see signs of it not holding a charge as well as it once did, I'm paranoid to not change it due to age. Anyone run one longer than this without issue? While this is a testament to Motorcraft, what other...

Is there a way to get a link to show a title as opposed to the URL? I seeing posts where these are displayed like they used to, but the link icon doesn't seem to allow me to do anything but display the URL as the link.

I've had mine disconnected for a while and don't remember where it goes. Anyone with a 2012 have any idea?

So yesterday, I mounted the TF Competitions on my car I purchased from Cotten waiting on some wider hoops from TF. I will be mounting the 325/30-20s I had on 11" wide OEM STVPP wheels in what will end up being 11.5" wide TFs. Reason for the wider hoop is to get to the same offset I was...

Anyone got any tips to take this thing apart? I've been fighting with it for over an hour now with no luck. The service manual leaves a lot to be desired. In fact, it's worthless.

I upgraded to VMP's triple pass, so this low mile AFCO, dual fan, dual pass is up for sale. Has the upgraded fan harness (note dual relays). $450 shipped to lower 48. This will fit any 07-12 GT500. SOLD! Mods, my post it note doesn't show up in the second pic, but does in...

Will the 15% discount apply to Whipple throttle bodies or only to superchargers?

Can someone give me better instructions on how these work? The packaged instructions are worthless.

Sold!

Anyone replace the bushing on top of your 8.8 differential with a polyurethane bushing? Since I pulled my rear end to install a Truetrac and a crush sleeve eliminator, I went ahead and burned out my rubber bushing and replaced it with an Energy Suspension bushing. My car is not back together...

SOLD - No longer available.

Sold!

Yesterday on my way to work, my Shelby was acting up. I didn't notice it, but when I went to run an errand later in the morning, I saw that it threw an MIL. It had 2 codes that I didn't write down, but both were related to the bank 2, upper oxygen sensor. My car is a little over 2.5 years old...

I bought a McLoed RXT twin disc for the 11+ GT500. The pilot shaft tool sent had the wrong pilot shaft bushing diameter, so I've spent countless hours bringing it to the right dimension with emery cloth. The bolts included were the wrong size as well. Luckily I had ordered some ARP bolts...

What are most of you guys running headers using to bolt them to the head?

I know there are several of you guys in and around the Houston area. I need to have my heads resurfaced and if I have to go that far I figured I'd get a 3 angle valve job. Any experience or recommendations with any shops that know their way around Ford DOHC heads? I've had Houston Engine and...

I'm in the process of changing out my short block from what ended up being a blown head gasket. After a loss in compression in the 7 and 8 cylinders, I knew the engine had to come out and it was going to go back together with better components. When FRPP announced the part number for the '13...

Sold!