I had a similar problem several years back.
Question have you changed your rear brake pads recently? If Yes.
They may have made a mistake and not screwed in the piston. If you dont screw in the piston the rear brakes dont engage properly and it
changes your brake bias to the front and messes...
me 32 is absolutely correct, vert springs are softer than coup springs. I had the same problem with my car with Eibachs and there is no mods other than replacing the springs or going coilovers which is where I finally found the solution. I owned Eibach Pro , H&R, and BRM kits. The Eibach...
I Have a full stock system off my 03 Cobra from the exhaust manifolds, catted midpipe, to catback . Only around 3500 miles on them. Been hanging in my garage since 2005. Alwasys thought I would need them for emissions compliance but that has been resloved and I dont need them
So I send oil samples of to Blackstone Labs for wear testing which measures oil degerdation, and contamination. I use to get is checked every year with each oil change (less than a 1000 miles a summer). I Bought my car new in September 2002. After 7 years of almost exactly the same results I...
Flat Stoppers work great and are very easy to use, but I also need to move the car around and the Harbor Freight Haul-Master dollys work just as well and allow me to move the car around. Just make sure you oil the wheels at the beginning of the storage, also they are about half the price and on...
Maybe I missed something but with that setup (ported factory blower, 7 lb upper, 2lb lower) why would you need to replace the fuel pumps? I run a ported blower, 5lb upper, and 4 lb lower without any fuel issues and have for years. And my son and I ported and polished my blower with my mill in...
My exhaust setup is almost as you described (mid length Bassani headers, catted Bassani X mid pipe, Borla stinger cat back). Now I installed it initially without cats but I ended up installing the high flow cats that came with the kit because I liked that better. Dyno wise the cats lost 5 HP...
Only two ways I know of are remove the master cylinder or drop the motor 4 inches. When I did it to paint the valve covers I lowered the k-member and motor.
I have wanted these for a while now. My wife has become her mother!! I have to have 9000 reasons why I need something, to replace something, I already have that works just fine but is a lot more work. Bad part is I have 2 low profile 2 ton aluminum racing jacks and 4 hydraulic lift jack stands...
Perfect timing!! My kids ranged from 7 to 10 years old in 2002 when I picked up my cobra and we had so much fun with it. This is what got all 3 of my kids interested in how things work. We were always doing something to the car (adding something or upgrading another), and usually one of the kids...
Yes you are correct Metco lower pulleys are NOT self centering. I've installed 3 of these over the years, my own car was the first and by far the worst, and all 3 had to be tapped in to center. Mine had .058" of play, the second one had .020" play and the last had .038" play. The second install...
I made my own press about 10 years ago, used it 40+ times over the years. Presses studs on without removing the hub or touching the threads. Presses the stud on from the head. Repaired dozens of studs.
This is a Blue Billetflow two ring Supercharger pulley set with a 2.76 ring (1800 miles on it) and a 2.93 ring and hub (0 miles on these).
Also a Billetflow 4 pulley idler set with 3 100mm pulleys and 1 90mm pulley (1800 miles on these)
$225.00 for everything. If shipping is needed that will...
I was wondering if I had to sell my 03 Cobra, :cryying: would I get more or less for it if I converted it back to stock and sold it and all the mods seperately. Or sold it with all the mods installed, with all the original parts included. Or sold it with all the mods installed, and sold the...
Does anyone have 17"X10.5" Bullit wheels on the back of their Cobra with the stock IRS? Any clearance issues? I've seen several with 18"X10" wheels but I don't want to buy new tires since the tires I got only got 2500 miles on them.
I have a a few part for sale.
1. New unused K&N FIPK- used the box for attic storage, but other than that everything is new in the bags.
SOLD
2. Motoblue SC pulley set USED 3000 MILES: Incudes--
1-- 2.93" MotoBlue Gen II SC Pulley
1-- 90mm Aux Idler pulley W/ mount...
It seems now the last little parking lot us Cobra owners could park in, has been siezed by the classic car NAZIS. Now unless you get there real early and park you will be told to move. Out of the last four weeks it's been full once and they had two cars in the lot we use. Today 50% of the...
I just got MM's strut tower brace and I was installing it and found the plates that mount to the towers would overlap my BBK cc Plates. This brace mounts to the front edge (top and side) of the tower not under the cc plate so theres not a lot of room. So I was wondering:
1. Without...