I had just finished purchasing several mods for my cobra and then had an opportunity to sell the car I couldn’t pass up. New owner didn’t want any of these mods (just what was currently installed on the car). So, I have the following aftermarket mods and stock pieces for sale. Prices are...
Still debating whether or not to put a lower on my new (ported) setup, but if the price is right then I will go for it.
Looking for the following :
Lower Pulley Kit with either 2lb or 4lb pulley
2.93 BF upper pulley (black strongly preferred)
3.2 alternator pulley
Either reply here or shoot...
like the title says, looking to buy 60lb sieman deka injectors. Would prefer paypal as the the source of funds. I'll kick in the extra 3%. either reply here or PM me with a shipped price. pictures would be great too (even more bonus points if you have a flow sheet to go along with them)...
So I've read many threads on what is needed for a ported blower setup as well as a small shot of nitrous and even some on a combo of the two. Various recommendations on what is needed or required....so I want to lay out what my current mods are and where I want to go to make sure Im thinking...
So here I am - 2003 ZY cobra with just over 90k miles on it. I've owned it since about 65k miles (bought it in october 2010). I love driving this car, so keeping the mileage low for resale value isn't really a concern at this time.
Current mods:
2.76" pulley with the 4-piece BF idler kit...
Ok, so I'm relatively new to drag racing tires and whatnot, so I've been searching the forums quite a bit. I *think* I have what I need figured out, but wanted to make sure it was the correct school of thought before I start purchasing things.
So I currently have an 03 cobra with stock...
Up for sale is my CoolingMist Trunk Mounted methanol kit. I have two different controllers for this, one is a variable controller (stage 2) and the other is a boost activated switch (stage 1).
The variable controller can be used for either an NA car or a boosted car. For NA it has a vacuum...
So my stock clutch has been on it's last leg for a while now. I really dont drive it all that hard except for the usual romp after a long day at work to hear the whine...and to put a smile on my face.
Anyway, just got a new Centerforce Dual Friction clutch put in with a new Ford Racing TOB...
got my new gopro last night and had to test it out. sorry for the strange angle, just wiped clean a spot on the bumper, put the suction on and started driving.
If you watch it full screen in HD you can see a small blue flame when I revved it a couple times before the pull.
:)...
At first I thought it was stupid....then it happened. The guy screaming like a little girl plus the fact the condom expanded so much had me laughing hard. :lol:
Went to a dyno day over the weekend. Just put my offroad mid pipe on and was going to see if I could hit the 450 mark (old numbers in sig with stock H-pipe.) Tune I have is already setup for the mid pipe so I thought I was good to go (back O2s turned off, etc).
I was all set for my 3 pulls...
Went to a dyno day over the weekend. Just put my offroad mid pipe on and was going to see if I could hit the 450 mark (old numbers in sig with stock H-pipe.) Tune I have is already setup for the mid pipe so I thought I was good to go (back O2s turned off, etc).
I was all set for my 3 pulls...
Contour HD 1080p camera for sale. It is used but in great condition. I pretty much always had it in the underwater case when I used it, even during normal use. I figured it doubled as a protective case anyway. I only used this thing a couple time when I went snow mobiling over Christmas...
American Muscle is having a sale right now on this guy brand new. I might just end up grabbing it from them, but wanted to check the market first to see if anyone had one they wanted to sell.
I believe that since I have an 03, that I would NOT need the O2 extensions. And I don't need the...
Noticed some oil on my garage floor. Got up underneath the car and sure enough, the rear diff cover is leaking. Sucks.
I didn't notice any kind of cracks or anything, so I believe the cover is still intact and not "broken", but what should my next step be? I found the fill plug, so I'll...
Just got the car dyno tuned on Saturday and it put down 434/451 on a mustang dyno. 2.76 BF pulley with all 4 BF idlers. I was able to reuse the factory belt since it was the correct size. I just bought a new gates belt that I haven't installed yet....will probably do that this evening...
Finally got some mods and took my car to get dyno tuned. :)
JLT intake
Steeda Catback
Stock H-pipe
2.76 BF pulley
4-piece BF idler set
NGK TR6 plugs
Diablosport MAFia
SCT X3 handheld tuner
it was a hot day (100°+), but still put down decent numbers. can't wait for it to get a...
I used this as a guide for cleaning the MAF. Cleaning the MAF . I used the CRC MAF sensor cleaning stuff on the MAF sensor after I got it out of the car. All I did was take out the air filter assembly thing and the MAF after unplugging it (of course I disconnected the battery first). Then I...
I did a few searches and couldn't find any information other than the occasional person wanted a smooth bumper instead of it saying Mustang or Cobra.
Has anyone ever made a rear bumper that said "TERMINATOR" instead of "COBRA" ? I think if done correctly, could look very nice. Anything like...
Hi guys. Ive been lurking here for a while and finally getting around to registering and posting. Tried a few days ago to, but log-in issues made that hard lol.
Anyway, this forum is a great place and I have really enjoyed reading lots of threads on any/everything that has to do with the...