I purchased this car new in 2003 and it used to be my daily driver up until about 2010.
The current motor was built and tuned by RET in Southern California and has been in for ~last 40,000 miles. It's spent the last few years in the garage with less than 1,000 miles put on it each year, so...
Any one know a place that has a good variety of license plate frames that will fit an Oregon license?
The registration stickers are on the bottom and are covered by most license plate frames.
I'm considering moving up to the Portland area and wanted to know how hard it would be to smog / register my D1SC Mach 1 with cams in OR. Are there any good shops in the area for tunes?
Something broke my fog light and I needed to replace the plastic part but don't know the part. Bulb is working fine, just need the outside plastic part.
Does anybody know the part number?
Hey everyone
My fiancee submitted a photo for a Facebook contest for a travel agency in LA. If you SVTPers with Facebook had some time could you please click on the link and vote for her picture?
This is the link to the Allure Plus (the travel agency) page
Sabrina in Allure Plus...
My neighbor has one of the older GoPros. I liked the way this camera looked, and the on-off switch on top is really easy to find even when it's hooked up to a helmet. 1080p recording is also very nice.
This is the camera I got
Contour | Products | Contour Roam
Thought I'd post some sample...
I'm looking to replace my rear tires...either a 285/35/18 or 295/35/18.
Don't really spend too much time at the track or drag strip. Mostly some spirited street driving every once in a while.
I'm a little concerned with the lower tread rating on the NT05 and don't mind paying a little...
Selling 4 Deep Dish Hypercoated FR500s (18x9 and 18x10). Interested in local pickup only.
I'm a located in Studio City, but willing to drive a reasonable distance to meet up.
Bolt pattern is 5 x 4.5" (5 x 114.3 mm)
Centercap Size is 2.5"
18x9 has a +30mm (1.2") offset and a 157 mm...
Does anyone know if the tensioner will fit with the Procharger bracket? i know there's a special Thump RRR Vortech bracket, but I don't know about Procharger. I called Thump RRR and they're not even sure
Just got a two year subscription for $8.
Magazine Subscriptions as low as $4.69 - BestDealMagazines.com
Use coupon code Irish17
5.0 mustang was on there too, but cost a little more.
What is the difference between these two pulleys?
Procharger Supercharger Pulley 4.00" Single Key USED - eBay (item 280577659052 end time Mar-18-11 12:53:17 PDT)
Procharger Supercharger Pulley 4.10" Double Key USED - eBay (item 280577658622 end time Mar-18-11 12:52:11 PDT)
Luckily I had alerts set up and noticed a $2,600 payment that they tried to send.
Chase hasn't really done too much, so I figured I'd post up the info that the person left in the account just in case they were stupid enough to put their real info.
They tried to send a $2,600 ACH payment to...
This is from a little car cruise the last weekend.
I've got a built and blown Mach 1....I'm pretty sure my new 03 cobra bumper added something like 150 hp. Before the bumper I dynoed at about 490 rwhp.
Other car was a 240sx with a 1jz supra engine. Usually dynoed at 425 rwhp but had...
Any one know a good place to buy one cheap hypercoated fr500 rims? Curb rashed the crap out of one 18x10 rim. American Muscle has them for $160.00 w/ free shipping but it's out of stock.
Taped off and power washed the engine bay after some engine de-greaser
Removed and re-painted shaker and spoiler
Then used Mother's Claybar, sealer, glaze, carnauba wax.
All done up...
Too bad it was all stop and go on the freeway....Mean looking car, but I wish they put a different wing on it. I'm not too familiar with Vipers, but I think it was a Viper ACR.
Does anyone know if Bassani mid-length headers + Bassani high-flow X + MagnaFlows (not the MagnaPacks) will pass a 95 db noise test? I think it's done from 20 inches from the tail pipe when starting the car?
I doubt my current set up (same as above except for SLP LM1s) will come close to...