I put a set of Tein springs on my daughters 08GT that I bought off of a member of this forum. The problem is the rear bottoms out going over rough roads, dips, etc. I assume it's just too low. I dont remember exactly what it measured when dropped, but I'm guessing 2 inches in the rear. I...
I just put 2010+ Gt 500 wheels on my daughters 98 GT. How do I reset the tire pressure monitoring system? I've been told it should reset itself, but it hasn't. And I've been told it needs to be done at the dealer to reset the computer to accept the newer sensors.
Any help?
http://www.svtperformance.com/forums/engine-drivetrain-256/881703-fs-complete-t-56-swap-w-mcleod-twin-disc-mgw-short-throw.html
I'm planning to buy this and I'm wondering if the driveshaft and transmission mount will fit in my 96. Also, will the harness work?
This came off my 96 Cobra. I made 520HP and 450TQ at 14 PSI with a T-Trim.
$125.00 plus shipping
Core dimensions are
11.5" tall
23.5" wide
2.5" Inlet/Outlet
31" Overall inlet to outlet.
Less than 2000 miles and in great condition. This is a VERY HIGH QUALITY piece. Sells for $475.00 on their site. $300.00 shipped
Ford Mod Motor Harmonic Balancer 8 Rib, 18% OD for 2V, 3V, 4V Mustang GT & Cobra | Racing Balancer | Innovators West
Im going to put a 7 qt oil pan on my 96 Cobra. It has an oil level sensor mounted on the drivers side of the oil pan. I believe this was removed on 98 and later models. Can anyone tell me if this can be turned off in the computer or if it can be eliminated? It doesn't use a typical bung that can...
Powder coated timing chain cover sold
SOLD!!!
I had this cover and one other black wrinkle powder coated about 2 weeks ago. I don't need this one. It will fit 96-98 Cobra. I ran an 18% Overdrive Innovators West crank pulley so the timing sensor has been machined to allow clearance. This will...
shifter sold Pro 5.0 T-5/T-45 shifter and Steeda billet Shift knob
This is off my T-45. Shifts great.
$100.00 plus shipping for the Pro 5.0. SOLD!!!!
$45.00 for the shift knob.
I bought this without realizing it would not work with the vortech bracket. It's got less than 100 miles on it. $275.00 shipped.
Thump RRR belt tensioner for 4v
PM-1003-90 Billet Aluminum Belt Tensioner with 90mm Billet Aluminum Pulley for Ford 4V Cars.
- Patent Pending Heavy duty Billet...
Sold MMR IMRC deletes
MMR IMRC deletes with gaskets $125.00 plus shipping. One fuel rail hold down screw is stripped. (you can see in the close up picture.) I just moved an 1/8 inch forward and drilled and tapped new hole.
This is the upper and lower intake from my 96 cobra. Includes gasket. The upper has been ported to accept a single blade throttle body. $400.00 plus shipping
LCleaning out the garage....
96 cobra upper and lower intake with gasket. Upper has been ported to accept single blade throttle body. $400 plus shipping
SOLD Spec stage 3+ 10.5 inch 10 spline with less than 3500 miles. $150.00 plus shipping
SOLD BBK Twin 65mm throttle body $175.00...
I've had the engine and transmission out of the car to clean up the engine bay and make some changes. First, the T-45 was not up to the task and has been whining and puking fluid since I raced and beat a corvette some time ago. I'd been nursing it along until we got my son's termi back together...
I'm running a YSI and I shred the belts every time I rev above 7500. I have 8 rib pulleys that were put on by a local shop so I don't know what brand they are. I spoke with Vortech and they told me that this will happen if the pulleys are not lined up correctly even if it's just a fraction. How...
My son bought the zex remote bottle opener off this site about a year ago and it didn't come with a switch. Im installing it in my 96 and I see that it has a red and black wire and when I test it on the battery it opens the bottle, but is there a way to close the bottle also with the switch...
My mods, hp and torq #s are in my sig. Any suggestions on transmission swap? Can a T45 be built to handle the torq I'm putting out? I'm only at 16psi and I will go to 19psi along with a shot of nitrous to help the low end torq until the YSI spools up. So my guess is that I will see somewhere...