Hey guys, just finished setting this up and cannot get one of the banks to read on the gauge. I have everything hooked up but it seems that only one side is reporting into the gauge. Your supposed to sync the gauge to the LC-2 module which ive done. However when I add power, only one side reads...
hey guys ,, I have an 03 with a 2.3 Whipple etc etc .. I was tuned at JDM on the dyno back in 2010 and made 650 rwh, it was tuned with Kooks LTH and High Flow Cats into Magnaflow.
ive recently had ARH headers installed with O/R X pipe .. Im assuming I now need a retune. I'm installing...
The ones on my 2.3 look old and I ordered all new from Whipple, but they dont give you the torque specs for these. Anyone know them ? Support gave me SC install guide, but these of course are all installed already at Whipple.
I have the FRPP fake OEM one and only figured that out after installing, so now i'm on the hunt for the Ford OEM one .. Maximum is out of stock on all theirs.
So some of you may know my car has the older 2 piece KOOKS long tubes. They are leaking and also sag really low. I have decided to pick up the ARH system which is about 1,750.00 (let me know if anyone has a code for cheaper). Now calling places for installation and it seems that's another 1,200...
my intercooler brackets have seen better days ... and before I rip off the front bumper etc .. to try and sand, paint the original one, does anyone sell new ones or rebrands?
Ok - this is what I'm dealing with.. Jump on highway cruising SOUTH about 60-70 steering wheel has a visible left to right oscillation which is constant .. now here is where it gets WEIRD .. make a U Turn and come back the same highway NORTH and Boom - wheel is solid .. no oscillation.
so it...
I have older 2 piece KOOKS LTH's and a catted mid pipe I'm assuming is from KOOKs.
Problem = The CAT from the left side of the exhaust has come loose inside and I'm constantly shooting bits and pieces of catalytic material out of the exhaust.
This weekend I went to remove the mid section to...
Hey Guys - sorry for the newbish question but I'm not very familiar with the SCT devices. I have one but never used it .. LOL anyway so this weekend I was mashing 3rd gear and missed 4th .. engine rev'd, then I put clutch in and went to 4th. Anyway BOOM right after that the battery light came on...
Thoughts guys ? I have old 2 piece Kooks long tubes which have the collectors that bolt to the headers. Over time they always leak and rattle, plus they sit really really low .. With BC Coil Overs, I have less than 1 1/2 if that ground clearance which makes it hard to drive around NJ roads...
So bought my cobra with 15.5k miles and it has a Spec Stage 2 .. But the clutch picks up at the VERY VERY top of pedal travel. Now I thought if replacing clutch but with LongTubes installed etc, shops charge your first born to install clutch.
Then I started thinking that a clutch with less...
Well I think my exhaust leak is at the collectors .. I can hear them rattle when i rev the car .. The bolts look rusty and im sure i'll just strip them trying to get them tight ..
thinking about taking it to a muffler shop .. Anyone have a good recommendation around Central New Jersey
Hey guys, just received my innovative Air/Fuel gauge and ordered the steering column mount for it .. of course its black and my interior trim is Charcoal .. What spray cans do you guys use to match up ?
Hey guys, looking under the front of my Cobra and I can see the brackets that hold the intercooler are starting to have surface rust ... What have others done to fix this ? How hard is it to remove from bumper ?
Are there replacements? or do I have to sand the stock ones? any help would be...
hey guys ive been wanting to change the hex bolts on the blower. Has anyone ever replaced these with newer ones? Some of mine have gotten discolored over time..
im fine with taking one off and ordering all new ones but was interested in the how hard to tighten them once I replace ?
Hey guys .. trying to help out my brother in law .. he has a data log from sct x4 .. but when we look at the reading for air fuel, it doesn’t match what the sctx4 was reading during the log. Gauge he has is an Innovative and reads both banks. In live link we have the equation to convert volts to...
Recently picked up a low mileage Cobra ( 15.5k ) miles .. it has 2.3 Whipple, upgraded fuel pumps, injectors etc .. Car was dyno'd in 2008 and made 646HP ...
Obviously that was a long time ago .. and my thoughts were to get a re-tune, but that will cost be 1,000 bucks .. ..
Question - Do I...
previous owner installed billet button covers on the steering wheel and im trying to get them back to stock .. anyone know where I can buy just the stock covers? I hope the billets are just covers
Hey guys, I have read different suggestions as to what does what when you turn the nut in or out .. Can someone please explain ?
Which tightens the cable and which way loosens ?
Also effects of each ? Which makes it hard to get into gear sometimes? Loose cable ?