Recent content by WydOpen

[Sold]

I recently purchased Coastal's Lockpick for my car primarily to run an aftermarket license plate bracket rear camera and have full use of navigation functions while driving. Pretty neat that it also allows you to install a front camera (something nice when you're parking and you don't want to...

I know there have been quite a few guys waiting for Craig to fab one of these up. He stopped by last week to take measurements and came back today with a pre-production version for fitment and finish. I have to say it looks great and I can't wait for him to bring it back from the...

Had it lifted last week and the weather finally cooperated so I decided to clean it up and snap a few pics... Setup... - Fabtech 8" four-link kit - 22x11 Moto Metal 950 wheels - 37x13.50-22 Toyo Open Country M/T's I bought the kit used, so I have to replace the...

The last time I dyno tuned my car (by Ed Clark) it was breaking up on the top end and he suggested it might be the plugs...fouled and/or gapped improperly. Previous owner installed NGK TR7ix (Iridium) plugs and had them gapped about 0.032". Today I replaced them with NGK TR6 plugs gapped at...

FS: '04 Oxford White convertible, 2.8H KB, 600 rwhp, 20K miles, $24K, Virginia... *** SOLD - SOLD - SOLD - SOLD *** After test driving the new 2010 Mustang, I'm sold and looking to get rid of my Cobra to pick up either a GT500 or Roush Stage 3. Thinking about going back to a coupe as well...

I called on the tuning services of Ed Clark and we used the dyno at All Aspects Motorsports in Chesapeake, VA. Very satisfied with the new tune. It looks like my fuel issues were resolved with the Lethal wiring upgrade. Also, Ed was able to get the idle smoothed out and now idles much...

Looking to increase torque and in need of a 4" upper pulley to fit a KB 2.8H blower and any brand 4 lb lower pulley assembly. I have a Kenne Bell 3.5" and 3.25" pulley for anyone interested in trading pulleys. Reply to thread or shoot me a PM. Thanks...

I had my car on the dyno on Monday and we saw dangerous drops in fuel pressure above I'd say 4,000 rpm's. It was dropping as low as 22 psi. The only thing I don't have installed is the wiring upgrade. I purchased it after leaving the dyno and started installing it today. The directions off...

I purchased new wheels and tires for my car and need to get rid of these. Previous owner purchased these wheels and tires for my car not too long before I purchased from him. They look much better in person than in pictures. I just needed something that would hook better for my power level and...

Sorry, it was late when I finally got the tires mounted and wheels installed on the car. I'm going to try and snap some better daytime pics tomorrow...

Anyone running 17x10.5 Cobra replicas with 315/30-17 M/T ET Street drag radials and having rubbing or clearance issues? My tires come in tomorrow and I'm getting them mounted up. I remember a few people mentioned having to grind down the bolt, but I can't remember if that was for 335 and...

The previous owner actually purchased the Spec Stage 3+ steel flywheel and clutch from Lethal Performance and provided the kit to me when I purchased the car. I confirmed through the Spec website that both are the correct part numbers for my car (SF84S steel flywheel and SF873FT clutch disc and...

Threw the car up on jackstands in the garage about a week ago. This past weekend I got quite a bit done. Installing the following: - Spec Stage 3+ clutch with steel flywheel - Liberty 26 spline input shaft - LDC cooling mod - TO bearing retainer sleeve - Fore billet fuel hat - Fore...

As the title states, selling the old exhaust system from my Cobra. Took both pieces off last night and ready for someone to come pick them up. The MAC cat-back is model number MAC-TK4699 (2.5" system with 3.5" stainless steel tips) that normally sells for about $375. The UPR is model number...