Recent content by TrueBlueGT

I'm just throwing this out there to see what happens. I don't expect to get a bite but if i do we'll see where it goes. I have a sonic blue 03 with 32k on the clock. It is a solid axle car. For those of you who have not clicked the back button I will go on. It has some nice stuff like most do...

I was headed east down a main four lane road through town earlier this afternoon. Traffic always stalls east of the third stoplight because invariably some stupid wants to turn left across traffic and shuts down the left lane. Knowing this, I got into the right lane early on and stayed there. Up...

I am considering upgrading my primary piece of equipment for my side gig. The sales person has shot me an extremely attractive trade offer to put me into a brand new machine. The spread between trade in price and my original purchase price divided by the number of hours I have run the machine...

I have a hairline split in a fuel tank on a tractor. It is a two piece 300 gallon total capacity tank. The split is in the left side saddle tank and it needs repaired. A replacement saddle tank is $1400 through John Deere not counting labor. I got a plastic welder after several tank repair putty...

I have never seen one. Can't seem to get my hands on one. I have my factory lower sitting on a shelf and a milling machine in the shop. What's so hard about modifying these things? I just read a post where the $800 was thrown around. Shitballs! We all like these things and there's enough...

Called up what used to be SuperTune in Stillwell KS about a quote on some work on my car. Place still has the same owner but a new name new manager and definitely a new pricing scale. I wanted my transmission built and a new clutch put in along with the various recommended accoutrements. New...

There was apparently a shake up at my preferred tuning shop. New name, new manager, same owner (owner does the tuning on my car so that's good). Anyway the new manager is focusing more towards full builds and less on single upgrades. I.E. no more installing headers unless its because they just...

I don't spend much time on here anymore so i have lost track of what's going on with the terminator world. Some time back I read about a caged lower setup being available which would accommodate an oversized drive pulley. I asked around some, got an email address, sent a message....no reply...

I'll be in your neck of the woods in a couple weeks. Just passing through but intend to get a room somewhere and spend the night to break up the drive. I bought a new diamond t trailer and my local dealer was between orders so he knocked off a grand if I'd go pick it up. So I'm heading to...

Was out for a drive tonight just cruising down the highway. Some jackass had lost a small(ish) wooden chair out of their vehicle and I didn't see it. Caught it with the right corner of the bumper cover and did a little bit of damage. It isn't a big deal and, as good as my bodywork guy is, he...

Had six thousand pounds of quickrete on a trailer. Went to unhook said trailer and the tongue bound on the ball. Put upwards pressure on the jack and tapped the tongue with a hammer. Tongue popped off, trailer shifted sideways as the jack failed at life. Jack stem peeled off the reach on the...

I've been on this website for over six years now & one consistent thing is people getting screwed in the market by unscrupulous sellers. This site is big enough that people can blend in & make some very vanilla posts to up their count while never actually being noticed. Then, next thing you...

Not "I was raised Catholic but haven't been in years" type catholic. I have questions for people who truly ARE involved with the church and incorporate it's teachings into their daily life. We can take this to pm's soon because I have no desire to deal with the muppets who surely will attack...

No he didn't enlist...he's eleven months old. My wife and I were at a wedding reception. Beautiful day, outside reception, and we brought our son's favorite little push toy. He was wobble-walking along and almost made it to the grass when he took a spill on the sidewalk in front of the church...

I have a good condition used magnaflow o/r x pipe for sale. It came off my 03 cobra but would also fit 99-01 cobras, mach 1's with manual trans, and 99-04 gt's with manual trans. Now, here's the bad part. Shipping on this thing is outrageous due to the size. If you want to pay the shipping...