Recent content by TRMN8RCRIS

  1. TRMN8RCRIS

    Installing ATS Brembos on the Cobra.

    I was talking about v3 not the v2
  2. TRMN8RCRIS

    Installing ATS Brembos on the Cobra.

    It looks like 2016-2019 CTS-V Calipers have the same mounting positions as the regular CTS. If thats so then thats a cheaper alternative (even though still pricey.. $500 per caliper) for a 6 piston BBK. Hopefully soon a cheap used V caliper will pop up on eBay so we can experiment. Those...
  3. TRMN8RCRIS

    Installing ATS Brembos on the Cobra.

    Sounds good Fyi, the width of the Wilwood 14” rotors is 1.25” according to their website, you can always hit up FTBR to get more accurate dimensions if that helps you.
  4. TRMN8RCRIS

    Installing ATS Brembos on the Cobra.

    @Mustang5L5 you still have the XTS calipers? Have you tried Wilwood 14” rotors for sn95?
  5. TRMN8RCRIS

    Fidanza DFX 26 spline kit

    Alright I'm getting ready to replace my worn out clutch and decided I should upgrade the input shaft. I came across the Fidanza DFX complete 26 spline package from Last Call Racing. The kit includes : Fidanza Pressure Plate Fidanza 26 Spline DFX Disk Fidanza Lightweight Aluminum 8 Bolt...
  6. TRMN8RCRIS

    FS: Kenne Bell Boost-A-Pump 40amp

    Selling KB BAP 40 amp for $200
  7. TRMN8RCRIS

    Considering Torco

    Hey SVTP Well my new motor is broken in and ready for the tune. I am considering torco since I ruled out E85 isn't practical for me and I have a torco dealer not 10 mins away from me. My setup is in my sig. With the 2.93 upper 4lb lower combo I should be around 15 psi. I am just looking for...
  8. TRMN8RCRIS

    Coolant Hose Part #

    Hey SVTP Anyone know the part number for the coolant hose that goes from underneath the radiator reservoir to the thermostat housing? Thanks!
  9. TRMN8RCRIS

    Flywheel spacer

    Anyone know the part number for the flywheel spacer/shim?
  10. TRMN8RCRIS

    Motor going back in

    Hey SVTP I have my longblock back from the machine shop and now it is time to start prepping the motor for the install. From the rear of the motor I know on both heads there is a sensor that needs to be bolted on. On the passenger head the rear heater tube needs to be on and the head cooling...
  11. TRMN8RCRIS

    Help Identifying Parts

    Just as the title states, Trying to figure out where these pieces go Thanks!
  12. TRMN8RCRIS

    Powdercoating problem

    So I need to know if I F'd up or what but I had my valve covers powder coated a while back ago, now the actual powder coating job came out great except for that inside the valve covers I have a thin layer of very fine sand, which I assume is from the sand blasting. I tried cleaning it off with...
  13. TRMN8RCRIS

    WTB Valve Covers

    WTB non powdercoated valve covers shipped to 92057
  14. TRMN8RCRIS

    WTB Factory Oil Cooler

    Found one Thanks!
  15. TRMN8RCRIS

    Oil cooler dilemma

    Anyone here deleted their factory oil cooler and run a remote one? Need a new one since the old one most likely has metal shavings in it but obviously can't find a new one due to them being discontinued. Thanks!

Top