Recent content by tjvineyard

Thread is in the classified section but I would really like to sell these without having to ship them: http://svtperformance.com/forums/showthread.php?p=5942759#post5942759 TJ

I am going to swap in some lighter seats as my car gets further and further from being a street car... *sigh* The stock seats are in good shape as the car only has about 15k miles on it. The driver side seat has a spot rubbed where your ribs are supported on the door side. The passenger one...

I am going to pull the motor and do some work on my Cobra. I have new headers and am going to rework the exhaust while it is apart. I converted to solid axle a while back to I have the cat back that fits a GT/Mach 1. It will not fit an IRS Cobra. It has less than 10k miles on it. I got the...

I am going to pull the motor and do some work on my 04 Cobra. I have new headers and am going to rework the exhaust while it is apart. Right now the car has BBK ceramic coated headers on it. These are the headers that were designed and built for the 99-01 Cobra heads. The ports on those heads...

Works great but now I need pistons. The short block takes priority so the stocker goes back on. You can have this piece of artwork to hold your belt tight for $250 (shipped). TJ

I am thinking about swapping to an auto in my Cobra. Anyone interested in a built T56? I upgraded to a 26 spline input shaft and revised (McLeod) bearing sleeve. I have a Centerforce DFX clutch and a Fidanza flywheel (8 bolt so you may have to swap depending on application). I have an MGW...

I have a set of genuine 04 Cobra wheels (chrome) with OE SVT center caps and F1 tires. Less than 15k miles. No blemishes. $700 for everything. I am in Austin and I really don't want to ship anything... TJ

Someone knocked the front bumper off my parked Cobra a couple of weeks ago. This is the second time someone has done serious damage while it was parked and not left any information... I can get a 2000 R urethane front bumper from a place in Wylie. I am going to be in Plano next weekend...

I finally got my LC-1 installed and wired. I am reading both analog outputs. Analog 1 is reading 'narrow band' voltage. Analog 2 is reading 'wide band' voltage. The LC-1 manual states that analog 2 is factory programmed for 0v at 7.35 AFR and 5.0v at 22.39 AFR. From those figures I...

I finally got my LC-1 installed and wired. I am reading both analog outputs. Analog 1 is reading 'narrow band' voltage. Analog 2 is reading 'wide band' voltage. The LC-1 manual states that analog 2 is factory programmed for 0v at 7.35 AFR and 5.0v at 22.39 AFR. From those figures I...

I still have more videos to post, but here is a start: White Eaton car 1st pull White Eaton 2nd pull Sonic Blue pulling into the bay Sonic Blue 1st pull Sonic Blue 2nd pull JC's killer Whipple trys to munch his clutch JC lays down big numbers anyway! Let me know if...

Has anyone used one of these or know someone who has? http://altronicsinc.com/pages/o2alert.html It looks like it might be pretty good for our particular needs. The sampling rate is ridiculously high and I am sure the sensor cannot read at nearly that rate, but the rest looks good. I...

I wanted to post a reply to: http://svtperformance.com/forums/showthread.php?t=146574&highlight=fpdm but since it is in the "archive," I do not think I can. Has anyone determined what the '05 Ford GT pumps look like? I was trying to do some research and I found this interesting...

Disregard I am putting my Whipple on and I am almost done. On the driver's side there is the rail that has three sensors in a row. The one closest to the firewall (and near the EGR) has two ports that look like they should have vacuum hoses on them. Unfortunately, I only have one hose...

Where are the conflicts that necessitate "low profile rails" with aftermarket (oversize) fuel rails and an aftermarket blower? Is this something that could be addressed, indirectly, with the new "shorty" 60 lb SD injectors I am starting to see pop up? Specs are at...