Just out of curiosity, is there some kind of adapter out there to rotate the oil filter 90 degrees to where it's positioned vertically with the engine and not horizontally, so that everytime I do an oil change it won't spill oil all over my k-member and power steering lines, etc.? I always...
Is there really any difference between the Stifflers or Maximum Motorsports FLSFCs? I'm leaning towards the Stifflers since I like how the seat brace is welded in opposed to bolted on the MM one. Is one better than the other?
I know I should know the answer to this, but I've never installed any aftermarket lower pulleys on either my Lightning or Cobra, and the only time I've had the factory lowers off was for accessory and supercharger belt replacement on both vehicles. My question is, while looking at the Metco 4#...
Has anyone ever put the red 10th Anniversary door inserts and seat covers in a DSG before? I think the red would look pretty badass in my DSG 'vert. Not really sure if it's frowned upon using 10th Ann. parts on non-10th Ann. Cobras or not? If I wouldn't have already had my valve covers...
So, my driver side headlight is the factory Ford piece, and has some sort of weird scratching/hazing that appears to be on the inside of the lens, as I've tried using a headlight restore kit on it and it didn't affect it. My passenger side headlight is a newer aftermarket headlight that was...
Hey Lethal,
I'm planning on ordering the JLT carbon fiber ram-air intake for my '03 Cobra and was going to get the carbon fiber heat shield to match, but noticed that JLT doesn't even show it as an option on their website anymore. I know your website still has it as an additional option in...
I'm looking at replacing the clutch, flywheel, and upgrading to 26 spline on my Terminator when I get home from deployment. I can't decide if I should get the FRPP aluminum flywheel or the Fidanza. I like how the Fidanza has removeable plates so I could always swap them out if I ever burn...
Where are you guys getting your white face gauges with the red SVT logo on them? I know Speedhut lets you customize gauges how you want them, but I went to build some and the custom SVT text looks tiny, and not the right font like OEM and the ones I've seen on SVTP and LRodder.
I recently rebuilt my 8.8 IRS differential and ever since I put everything back on the car I get a nasty sounding "pop/clunk/grind" noise coming from either the transmission or the rear end. It happens when I've left my Cobra parked in my garage and left in gear (usually left in 4th) for a few...
I noticed this on my '03 Cobra the other day that there are noticeable gaps between where my trailing edge of both quarter windows meet the bottom of the convertible soft top. It's large enough that wind noise is heard inside the car while driving so I know rain/snow etc. has to be getting in...
I recently bought a TF stud kit for the differential bearing caps on my '03 Terminator with factory IRS. Upon installation, I noticed the studs were too short and contacted TF tech support who then told me this kit only works on the iron solid axle 8.8s. The studs have only been hand inserted...
Are there any decent stud kits for the factory IRS aluminum case differential bearing caps? I have the Trick Flow stud kit from Summit, p/n TFS-85101-1, but upon install I noticed the studs were way too short. Emailed TF tech support and apparently these only work on the iron SRA 8.8 bearing...
SOOOO...tonight I decided to install my MMD hood strut kit that I bought from American Muscle. It was supposed to be an easy, quick install, and I started by removing the two nuts on the passenger side hood support. The studs and nuts that are installed in the hood were coated in paint from...
Does anyone know if the Trick Flow ARP 8.8 differential bearing cap stud kit, p/n TFS-85101-1 will work in our differential cases with the stock caps? If not, would I need to go with the Mark Williams caps or a whole other stud kit from somewhere else?
I've had my Cobra on jack stands for about 5 months now. The first 4 months I had the rear supported only on the subframe while I took my differential housing out and then I decided to put jack stands on the front supporting the k-member so my front tires don't get flat spots. I was adjusting...