Recent content by snkevenom

:fm:i have a 99 cobra motor built for a turbo. it has a slight miss at idle that just sounds like a cyclinder falling every other rotation you can see the rpm drop 200-500 rpm when it stumbles and around 1500-2000rpm under light load it gets a little rough but smothes out at rpm climbs . motor...

i have a 99 cobra motor built for a turbo. it has a slight miss at idle that just sounds like a cyclinder falling every other rotation you can see the rpm drop 200-500 rpm when it stumbles and around 1500-2000rpm under light load it gets a little rough but smothes out at rpm climbs . motor has...

ok i dropped a 03 twin pump in my tank for the turbo i am putting on but had to buy the fuel level sender and add it to the pump i am trying to figure out where the white wire from the fuel hat hooks to the level sender , i figured it was a ground like all the other pumps have so i bolted it to...

ok may sound stupid but does any one have a pic or know where the white wire coming from the hat of the pump hooks up on to the fuel level sender? when i got the pump it did not have the fuel level sender on it so i had to buy that to add on but i cant fid any pic or any thing where it goes so i...

i have a 62-1 master power turbo that only has 15 miles on it, i need to upgrade to a t70 or t76. it has a .70 cold side and a .96 hot it also is still has a warranty on it till jan of 09 looking for 450.00 or OBO. if interested email at [email protected] can send pics

i have a master power turbo 62-1 with a .70a/r cold side and a .96 hot side, the turbo has seriously 15 miles on it. When i ordered it i thought i was getting the t-70 but the guy that sold it to me had it wrong on his page and when i found out he would not return my calls or emails, now i have...

ok on the turbo with the v-band clamp style what size do you use? measured mine from lip to lip and it said 3.5 but not seeing any one running that they are all 4 inch? what one do i need to order3.5 or 4?

i have a 99 cobra and i am close to mounting the turbo up maybe today or in a few more days its a custom built home kit , my question is on some of the turbo kits i see people build like mine they have the right side coolant hose blocked off where it goes from the water neck down to the lower...

has any one put a turbo kit on their new edge cobra with out removing the stock k-member? and also how hard was it tho run the pipe

ok i have a 62-1 master power turbo with a .96 hot and a .70 compres. is a 38mm wastegate good to only going to be running 8psi on stock long block for now? also what are good brand names other than tial seeing what all is out there and if i can get by with out dumping $200 in this deal?

any one running this set up with a mafia maf extender or any thing or is it even pos?

like the title say anyone have this setup? looking to run this on low boost for now but next year looking for 600+whp any one have any ideas? just ordered it.:shrug:

i just ordered a masterpower 62-1 turbo looking to but on stock 99 cobra motor just wanted to see if any one had this setup or know of one? also what hp is this turbo good too the guy that sold it to me says 700 others say 600 but after forged motor next year looking to run 600whp+:shrug:

here's my question i am thinking about buying a mark 8 motor stripping it all down to a bare block and putting forged h-beam rods and forged slugs in it and dropping it in my 99 cobra so i have less down time any one know if all my cobra stuff will bolt up to the block? (timing...

ok i have a stock 99 cobra looking to put either a masterpowre t70 or GT-45 on it what would be better to bring in quick boost only looking at 8-10psi right now with a safe tune, also next year building the bottom end and going to run 15+ psi any one have this set up?:shrug: