Recent content by Snakey03

  1. S

    FS: Complete 9" Axle Setup 94-98 Width

    This is the complete rear axle setup to put a Bullet Proof 9" in a Mustang FULLY functional ABS and Factory Cobra Brakes!!! Includes: the housing, Strange S case, Daytona Pinion Support, 1350 yoke, 800 HP capable reinforced 31 spline Trac-loc, Moser 31 spline axles...
  2. S

    2009 Changes/Mods

    I got a few of my planned changes for this year done. Here's some pics so far. The first pic is what the car looked like last year.
  3. S

    FS Deep Dish Anthracite Cobra R's

    Fs Deep Dish Cobra R's - STLMustangs Forums SOLD
  4. S

    FS Deep Dish Anthracite Cobra R's

    Fs Deep Dish Cobra R's - STLMustangs Forums SOLD
  5. S

    FS: 03 Cobra Silver 10th Anniversary

    I am the original owner, bought her in July of 2003. 9200 miles #354 of the 2003 10th Anni's #7540 of the 8394 Performance bolt ons: Factory Lightning pulley 2.93" 12" Anderson Ford Power Stack filter Mac ceramec long tube headers Mac Pro chamber H-pipe Magnaflow cat-back w/ 4" tips...
  6. S

    Lightning Parts FS

    First up my Customer Dave wants to go a different direction with his Lightning so he wants to sell most of his present combo: 2.3L KB, JLP powerflow plenum, 3.5" and 3" upper KB pulleys, 9" one piece lower and belts for both pulley combos, and a cold air kit. each pulley and belt has about...
  7. S

    Project Lightning Dyno Pull

    Woohoo, I took my customers 02 Lightning to Stiegemeiers today! I don't have a dyno yet. It made almost 540RWHP and 600RWTQ SAE!!! the tune still needs alittle work, it's a bit rich. Hey Moderator below it says i can't add attachments???can i email this to someone and they can add it to this...
  8. S

    Want to trade IRS

    Anybody with an 03-04 Mach 1(preferably), interested in swapping complete rear suspensions?? My IRS is stock with 7400 miles on my 03 Cobra. I have a Magnaflow catback with 4"tips and the original catback also. thanks, Greg
  9. S

    New Wheels Installed

    just installed my new wheels from OE Wheel Distributors they are the 96 Cobra R Deep Dish series 17x9s on front 17x10.5s on the back. Here's the link The rears do need a small spacer either 3/8 or 10mm. I plan on getting these even though the tires would only rub at full suspension droop...
  10. S

    FS: Factory 03 Cobra Parts

    The following parts are off of my 03 10th Anniv. It is silver with 7500 miles.... Hood............................$400.00...SOLD!! Hood Blanket................$50.00...SOLD Front bumper with bottom deflector tabs on driverside broke when removing attachment plate for new...
  11. S

    W T B

    does anybody have a pass. side smoked headlight for an 03 SVTF and,or a hood???? thanks......greg
  12. S

    wow 440 RWHP

    wow yesterday i installed a 2.93 upper and a predator tune by James at RWTD!! i already had 398 RWHP with a 12" Powerstack filter and a Magnaflow cat-back w/ 4" tips. now i have 440.35 RWHP and 439 TQ. but i think it is a tad lean so i need some opinions on the A/F ratio. the dyno chart is on...
  13. S

    Lightning Blower snout

    does the front of our eatons interchange w/ the lightnings??? a friend bought a whipple for his L and said i could swap front snouts w/ him!!! neither of us have a pulley puller, but he said the fronts will swap. what boost would i see with a L pulley and what belt should i run???? thanks in...
  14. S

    New best time.

    Was at MAR today. With just a magnaflow catback & a 12inch powerstack filter. I ran a 12.45 @ 113.4. With a 1.909 60ft. On 275/40/17 nittos and I launched at 5000 rpm. With no wheel hop.
  15. S

    New addition

    well i just set up a web page at cardomain.com cool place!!! please check it out guys & gals my latest toy is on page 3!!!!!!! hope this works the link:http://www.cardomain.com/memberpage/545199/1 thanks, greg

Top