Finally got my Clutch replaced.
~Installed a McLeod Street Pro clutch kit, McLeod flywheel with new FRPP bearings, FRPP clutch fork, TO bearing sleeve, MM clutch cable kit with heat insulators, and a new FRPP hi-torque mini starter.
- I also got the chance to soak the bearings in a coating of...
Most difficult part to find on the planet! Radiator cooling fan assembly!
~1996 Mustang COBRA~
If you want to experience what retardation is like, call some of your local parts stores, including Ford, AM, CJ Pony,Leathal Performance, and all the other big ones. No luck unless you want a unit...
I am supplying all of the parts to have clutch kit installed.
can you tell me what your labor only cost was??
~First quote is $650.00
******
im providing clutch kit, flywheel, FRPP throw out and pilot bearings, throw out bearing retainer sleeve, clutch fork, fork pivoting stud bolt, MM clutch...
Im excited to be able to have you guys help me out choosing a new exhaust system for the a guy I (and everyone else) works for.
Im going to provide him a list of parts for a full system.
Just started researching. I have a coupe and a Cobra, I designed the exhaust with both of these, very unique...
Can you please provide me a recommendation on a motor starter for the 1996 4.6 4V Cobra?
Quality, ease of installation, and of course function.
Engine is stock.
Thank You,
-Robb
I need to replace the starter on the '96 and need your help choosing a reliable starter with a reasonable price if possible.
I came across a FRPP hi-torque unit but it runs for $290.00.
Ill pay what ever it cost for a quality unit. Please let me know what you know of.
Thanks, -Robb
I have my single disk Street Pro kit :smmon: from McLeod ready to put on. I can't seem to find much conversation in regards to "first impressions" or "years of use". I'm happy as $hit to have it, very anxious, next best thing is to read about it I guess.
I need help with my '96 cobra, hoping some Terminators can relate to the alternator upgrade.
**-I replaced my alternator with a 200amp unit & 4 gauge wire & in-line fuse. Hooked up the alternator with the factory wire and the 4 gauge wire on top terminal post. Ran 4 ga wire to fuse block...
Just purchased a 200amp alternator and 4 gauge wire.
I am in dire need of assistance with wiring the 4 gauge wire from alternator to battery. Also have an inline fuse block.
**Do I leave the factory wire on the post connection with the new 4 gauge wire?
**And does the new wire just go from the...
I want to put 1" spacers on rear wheels. These rims have brand new rubber on them and I will be replacing suspension in coming months and will live with these rims for a while.
-Does the wheel spacers on rear only throw off alignment enough to effect tire wear or drive ability?
Any experiences with replacing a broken throwout bearing retainer? What it look like where the stress split it?Change out a TO Bearing retainer before? What were the symptoms while driving?
Thanks
I am researching an alternator replacement for the Cobra. Wanted to know what products were successful for you guys & gals. It's a stock Cobra with some miles on it. I occasionally (increasingly) see a red battery light come on for 5-10 seconds upon start-up. I have a defective drivers side seat...
I am about to schedule my clutch replacement and need to know if any more parts are needed. Mainly, do I need a new throw out bearing retainer sleeve? Adjustable pivot ball?
LINK:http://www.lethalperformance.com/lethal-performance-t-56-throwout-bearing-retainer-sleeve.html...
My Cobra's paint is now starting to flake off. What have others done to rectify issue? Re-paint entire car with "Ultra White" paint? Where, how much, insurance claim, Ford ever accept responsibility? I need to do something soon.
Thanks, -Robb