Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
rattle_snake's latest activity
rattle_snake
replied to the thread
Driveline clunking while driving
.
With some miles put on the new gears all is well. The 3.73 ratio at only 5% is noticeable. In cooler temps with not-so-sticky NT05Rs is...
Apr 25, 2024
rattle_snake
replied to the thread
Driveline clunking while driving
.
Finished out gear setup and install. Had to make and modify a few tools and parts to get it done. Took a few pinion depth...
Feb 12, 2024
rattle_snake
replied to the thread
Driveline clunking while driving
.
Ford has changed the manufacturing style of 8.8 gear sets since the 2000s. Used to be 5 cut and now 2 cut/face hobbed. So wear pattern...
Feb 5, 2024
rattle_snake
replied to the thread
Driveline clunking while driving
.
Thanks. I couldn't find them either until I cleaned everything. The oil film made it not possible to feel the few broken teeth in the...
Feb 5, 2024
rattle_snake
replied to the thread
Driveline clunking while driving
.
Cracks are deep. would have failed very soon. 3.73 going in instead of 3.55. This is only a 5% change. Trap speed of 120 should be...
Feb 2, 2024
rattle_snake
replied to the thread
Driveline clunking while driving
.
Did above test, noise in rear end. Put on lift, disconnected driveshaft. noise in diff. Pulled the diff to inspect Removed cover for...
Jan 25, 2024
rattle_snake
replied to the thread
Engine dies, code 1233
.
Why? I verified power at FPDM thur BAP. replacing CCRM at that point makes no sense. blindly throwing parts at it.
Nov 22, 2023
rattle_snake
replied to the thread
Engine dies, code 1233
.
Go back and read post #18, synchronous voltage and pressure measurement failure. Seems you don't understand what your talking about...
Nov 22, 2023
rattle_snake
replied to the thread
Driveline clunking while driving
.
When I can get some time I plan to put the rear on blocks and spin the drivetrain up to speed, shut engine off and listen. stethoscope...
Nov 22, 2023
rattle_snake
posted the thread
Driveline clunking while driving
in
Driveline
.
After 1st gear WOT pull (no hop) my cobra has developed a clunking noise that is dependent on vehicle speed, not engine speed. Clutch...
Nov 16, 2023
rattle_snake
replied to the thread
Resonators with o/r h pipe and borla stingers
.
I put resonators (aka 12" long 2.5" cherry bombs) in a mac prochamber mid pipe. Ran several mufflers; Flowmaster Stingers magnapacks...
May 17, 2023
rattle_snake
replied to the thread
Engine dies, code 1233
.
Year later I get code 0193 again... Aghhhh I had bought a OEM sensor from Ford, original lasted 17 years, and new only 1 year? Cleared...
May 17, 2023
rattle_snake
replied to the thread
Engine dies, code 1233
.
When in failure mode I tried holding to floor and it would fire but not run. Once output from FRPS was correct it starts fine...
Apr 27, 2022
rattle_snake
replied to the thread
Engine dies, code 1233
.
I think I found issue, FRPS Did datalog and fuel pressure correlates to mech gauge. commanded DC adjusts as expected. I don't see...
Apr 26, 2022
rattle_snake
replied to the thread
Engine dies, code 1233
.
Ok Thanks Vinnie. Did some more testing. Let car run until it died. Observed the mechanical gauge vs what is reported over OBD. They...
Mar 29, 2022
Members
Top