Recent content by radtexas

If you have something in decent condition shot me a PM price and a photo if you would. Thanks

Corsa Axle backs #14311 for 05-08 GT & GT500 They have about 25k miles on them. I first had them on an 07 GT and they sounded great. Sold that car and put them on my current 08 GT500. They fit fine but the "X" on the Shelby causes them not to sound as good as when I had them on my GT so...

I have a slight shake in my steering wheel around 55-60. But it does not do it all the time. I have had the same stretch of road with some shake and then some times smooth. It is more of a nuisance than a major issue but it just bugs me since I am confused on the cause. I have put on new...

I am wanting to do a little experimentation with a mock up crossover box similar to what prochamber has. Because of the angle the GT500 comes in/out at the crossover it is basically opposite the design that prochamber does on the other stangs so I am going to have to get creative. I am...

I currently have on my GT500 some Corsa Sports 14311 that I had on an 07 GT. On the GT I loved the sound. On the GT500 not so much. I know the "X" is probably part or most of the problem. GT had a nice deeper tone but on the GT500 has a raspy tone at middle to WOT. Sounds nice at idle and...

I am debating on wheels which is taking forever to decide. Wondering if anyone has got any Steeda Pentar's on a GT500 they can share photos of? I am thinking 18's as I prefer the look more. However since they only have 9.5's I am thinking of widening the rears to 10.5's so I can get a little...

I got this cover with a new car purchase deal. Cover has never been out of the box. From this add you can see they sell for about $260-$270. Great price for a new, never taken out of the box item. Asking $175 ITEM Part # 5R3Z-19A412-CA Mustang Car Cover Ford Parts Direct

I have and still am deciding between widening my stock rears to 10.5 or finding a wheel at least 10.5 wide. Unless you go custom wheels it is a hard find. And even though I like the looks of custom TF & CCW wheels I just don't have the budget for them. I found these FR5 wheels that are...

Well after working out a few bugs I got to finish installing the CAI & tune from Jay. I did go from stock to this and it is like a new car. The throttle response is instant. The SC is loader which is a good thing. Just sounds meaner. I don't hear the air sucking in the filter like I thought...

I had this SCT X2 tuner for an 07 GT. I loaded the tune back to stock when I sold it and keep the tuner. I got a new tune for the JLT CAI and when I go to load the tune it tells me "Wrong Vehicle". I thought when you loaded back to stock it was ready to load tunes for another car. What am I...

I got this for an 07 GT/CS and it worked great with a SCT X2 tune from Brenspeed. Sold the car and it has been in the garage for over a year now. Need to pass this on to someone else. Still in good condition and had less than 15k miles on it. Filter was cleaned and just need re-oiling. C&L...

Just wondering if someone has some done and they are just sitting around. Looking to widen mine but if I can keep from it I will just buy.

Never done or even been around a dyno run so I may ask stupid questions. I am wanting to get a baseline run and one after adding a CAI tune to see what actual difference I get and end up with. Are all dyno shops the same as far as gathering the data? Are there certain things I should ask...

I found a set of GT500KR springs, struts, shocks. I read the write up by Tob. He got some new Ford upper strut mounts. Not sure which version -A, -B, or -C. He was able to get his in specs without adding caster camber plates. But they are riding the negative camber line. I was thinking...

I know you need caster/camber plates. I am wondering if when lowering you should swap out the front strut mount to the latest version "M-18183-C" What version is on the 2008? (-A?) Never installed caster/camber plates and do you reuse your strut mount with them? Just trying to figure out...