Own a 2020 Hellcat and anything below 60mph will just blow the tires straight off. Also the traction control in track and street mode kills power a lot makes to allow the car to gain traction and you can tell right away. In sport mode it just spins tires until you let off the throttle. Good run...
finally added some Kooks Longtubes headers and off road Kooks xpipe to my mach 1.
as always pro dyno does excellent work. fastlane motorsports and pro dyno are the best on the east coast.
old setup was custom cams, JLT CAI, stock Headers, magnaflow catted xpipe, borla stingers, and...
hope you guys like it,new to photography:beer:
DSC_0040 by mr proper, on Flickr
MACH 19-8 (3) by mr proper, on Flickr
DSC_0061 by mr proper, on Flickr
DSC_0041 by mr proper, on Flickr
MACH_ by mr proper, on Flickr
mach1 rear by mr proper, on Flickr
logo by mr proper, on Flickr
MACH 19-8 (5)...
here some recent pics of my mach 1 (covered in Pollen:nonono:)
Front Wheels are 17x8 with 245 invos. (Street Setup) 19Lbs each.
Factory Mach 1 wheels 17x8 are 26Lbs EACH.
Rears are 15x9.3 with 275/50/15 Nitto DR NT555R. 14.9Lbs EACH.
AFS Mach 1 17x10.5 Wheels with 315/35/17 mounted NT05'S...
nothin crazy like some of our fellow svtp'er:D but i thought i share it.
just had the car re tuned at pro dyno fort mill sc.
Custom spec'd cams,JLT Cai, Magnaflow catted xpipe and borlas.
cams are spec'd for midrange and peak hp at 6krpm... Tiny :)
it put down 334rwhp and 333rwtq with stock...
code p0174-(bank 2 is lean) showed up yesterday
2004 mach 1
here is datalog at idle and some driving
code showed up at low rpm driving 15-20mph, car still drives fine.
car has cams,cai,borla, and catted midpipe and custom tune.
drove the car 300miles since cam install and yesterday the code...
code p0174-(bank 2 is lean) showed up yesterday
04 mach 1
here is datalog at idle and some driving
code showed up at low rpm driving 15-20mph, car still drives fine.
car has cams,cai,borla, and catted midpipe and custom tune.
drove the car 300miles since cam install and yesterday the code...
hi
i just had a new clutch spec stage 1 , SPEC aluminum flywheel, TOB ,Pilot bearing and clutch fork installed, and on my way home the car chatters really bad when iam in 1st gear and leaving a stoplight, it shake the complete car!i can hear a loud chattering noise in neutral and my clutch...
been on a on and off diet (love fast food:D) for about 12-15months and finally done!! now iam starting to eat clean and try to go Big! went from 186LBS to 142LBS!!! Hard work finally payed off!!!
Thanks Fellas just really Proud just had to POST iT:thumbsup:
1ST Pic is at 186LBS ( iam 5ft 7)...
1st up i used the search button on all my mustang forums and i could not get my answer! i was in need for new rear tires,
iam running now 285/40/17goodyear gs d3( afs 17x10.5 wheels rears) there now 6years old still look great, but i cannot floor my 1st gear without spinning my tires! i have...
check my craiglist ad
you can PM me or email me over craiglist!
thank you for your interest
prefer local pick up
18inch ford mustang GT500 SVT fits 2005-2010 mustang Wheels+Tires