Recent content by MACHSTR

  1. M

    Eaton swap on NA aluminator.

    My best advice is find a donor 03/04 cobra or find a guy going turbo. It's easy if you have all the parts. I built on an aluminator short block at the same time and dropped it all in. Once I upgrade my exhaust the tuner said I should make 500 to the tires. I'm running a 2.76 pulley on a high...
  2. M

    Eaton swap on NA aluminator.

    Just finished the swap. It was worth it!
  3. M

    Eaton swap problem

    Thank you I will check that out, it is running lean though....
  4. M

    Eaton swap problem

    Just finished my eaton swap on my mach 1. Upon first start it ran good for about 3 or 4 minutes so I took it to get dyno tuned. When at the tune shop it started idling horrible and wanting to die when it gets warmed up. He has a base tune on it but can't fine tune it until I find the issue. It...
  5. M

    WTB 99/01 amber tail lights, 99/01 front bumper, 03/04 mach 1 front seats

    If you got some 99/01 cobra amber tail lights, a good 99/01 Cobra bumper, or a set of 03/04 mach 1 seats in good condition for sale with no rips or tears please let me know.
  6. M

    03 Cobra fuel tank vs. 99+ fuel tank - A comparison with pictures and notes

    I'm bringing this back from the dead lol. Will a sending unit off a mach 1 stock fuel pump work on cobra dual pumps? I got the hat/pumps, but no sending unit. Of the 4 wires, 2 of the inside wires have been cut. The 2 that aren't cut run to the pumps. I'm assuming the two that are cut both went...
  7. M

    Oil Cooler Adapter Compatibility

    I ordered a used 96-98 cobra oil cooler adapter part # F6ZE-6884-BC for $80. I have a 03-04 oil cooler. I cracked the oil pressure sensor threads on my 03-04 adapter part # F8ZE-6884-AA. Visually they look exactly the same. Does anyone know if there is any difference at all in the part? If there...
  8. M

    Oil Cooler Adapter Compatibility

    I need to know if the 96-98 adapter will work with a 03-04 oil cooler. They look the same.
  9. M

    FS: 03/04 Oil filter/cooler adapter

    Do you still have it?
  10. M

    Aluminator swap

    Thanks for all of the input and opinions. I will probably just go with a reputable tuner and run what I go with a safe tune. I live just south of Houston, TX. Does anybody know of any good tuners close to my area?
  11. M

    Aluminator swap

    I posted this over in the mach 1 section but have gotten no replies.... Anyway I got a 2004 mach 1. I got a new old stock naturally aspirated 4.6 aluminator (10:1 compression, forged internals) with 03/04 cobra heads already on it, cometic gaskets, and arp studs. I am going to put an eaton on...
  12. M

    Importance of pulse wheel?

    I bought a shortblock 4.6 NA aluminator and am going to put an eaton on it and run low boost. I know I may sound like an idiot but when I was installing the timing kit, I put a unused pulse wheel on that I had brushed some rust off of because it had been sitting for awhile. I already got the...
  13. M

    Eaton swap on NA aluminator.

    Thanks for the advice Serge. Ok, I got the 39 lb injectors on the way, I have the cobra fuel pump & hat with a stock mach fuel tank, sct2600 "big air" MAF on the way. 2.76 pulley on non ported eaton m112. LFP extreme intercooler, LFP dual pass heat exchanger. Metco idler pulley. As I stated...
  14. M

    Timing question...

    Nevermind, I figured it out!
  15. M

    Eaton swap on NA aluminator.

    I am in the process of finishing my 4.6 NA aluminator engine. I got a killer deal on it. I wanted to build a motor with a little less compression for the supercharger, but it was so cheap, I couldnt pass it up! I have an eaton swap kit and all I need is the injectors and a maf sensor. The eaton...

Top