Take $2800 shipped to Plano, TX 75074? Last set of TF Chicane's I bought, that's what I paid. Looking at about $200 to ship via UPS. I've done it three times in the last year. HA!
Jason
Has anyone actually done an airbag delete and gone with aftermarket airbags in their 05-09 Mustang or GT500? I pulled and sold the seats before I could ohm out the resistance of the airbag in the driver and passenger seats. There is little documentation out there on this but what I have found is...
Looking to pull the trigger on one of two Lightnings this weekend. Both are negotiated to same price locally. Which one would you go with? I'm leaning towards the '01. It'll be an unmodded daily, while I begin the real work on my GT500.
TIA, Jason...
This is cross post from the GT500 forum, can anyone at VMP confirm that the '08 GT500 ECM pin 10 in the middle harness is a clean tach output? I've read several posts in the Coyote forums that this is true for their ECM. Hoping I can pin out this same pin in the GT500 harness to get a clean tach...
I've done some research and see that pin 10 of the middle connector to the ECM is a good tach output signal. You simply need to pin out the harness. Can anyone confirm that's the same for an '08 GT500? I'm running an aftermarket tach and the Tach Adapter isn't getting along with my WOT Box...
Hey guys, need some help. I've been running a N2MB WOT Box for a little while now. No issues. Decided to add a Tachometer to the mix using AutoMeters Tach 9117 Adapter.
Basically, the WOT box and Tach Adapter wire in the same way. Cut the coil wires in half under the BEC solder the red wire...
For those of you that have installed an aftermarket Tach in your car, where did you get your RPM signal? Did you go to the negative wire on one of the coils, pin 25 on the middle ECM plug or did you go with a Tach Adapter. Looking to do this install soon and looking for path of least resistance...
Just like the title says. Looking for stock upper and lower grille that will fit a stock GT500 bumper. Can be broke or torn up to a point. Looking to cut them up and try something new.
Let me know what you've got and what you want shipped to Plano, TX 75074. Money in hand. Don't want to have...
Spent the day cleaning and preping the garage. It's the first nice weekend since Christmas, so I'm getting up in the morning to do a blower swap and assorted other supporting mods. Any last minute tips to make my life easier? Installing the following:
VMP
New TB
New MAF
New plugs
New...
do you guys have the ability to order Weld or Bogart rims? Specifically looking for Weld RT-S in black anodized, 17x5 fronts and 15x10 rear, with lugs, hub centric rings, tpms sensors and tires. If Bogart are available I'm looking at the D10 two piece design.
TIA,
Jason
Looking for a full set of Weld RT-S wheels, lug nuts, TPMS and hubcentric rings. Thinking either S71 or the S77B in black anodized.
Any vendors here sell a complete setup?
Thanks,
Jason
Hey Sid, I've not been receiving notification of thread update, or notification that someone has sent me a PM. I've double checked and my e-mail is correct in my profile. Any other thoughts?
Jason
Clutch was going out, long story short... Was getting worse and needed immediate help. Van reached out to me directly, within a few IM's we settled on what all needed to be done and he got the parts in the mail immediately. I spoke with Van Wednesday late morning and had parts sitting on my desk...
Are there alignment holes for the fender badges behind the Cobra emblems? I've got some old Cobra emblems that don't have the centering pins but I can't remember if the holes are there, or not. Asking about an '08 model GT500.
TIA,
Jason