Recent content by fallingup693

  1. fallingup693

    WTB unmarried ready to go SCT x3/x4 programmer

    Like the title states. Looking for a new or used SCT x3 or x4. Let me know what you have and the price shipped. Thank you.
  2. fallingup693

    WTB 26 spline input shaft

    Like the title says... Let me know what you have.
  3. fallingup693

    Intercooler delete on methanol?

    I've been thinking about doing Methanol injection on my Posi blower but I have a feeling if I mount the nozzles pre TB that the intercooler will heat up the air before it hits the combustion chamber. Is there a way to mount it efficiently after the intercooler? Has anybody deleted the...
  4. fallingup693

    Intercooler Delete with Methanol question

    I've been thinking about doing Methanol injection on my Posi blower but I have a feeling if I mount the nozzles pre TB that the intercooler will heat up the air before it hits the combustion chamber. Is there a way to mount it efficiently after the intercooler? Has anybody deleted the...
  5. fallingup693

    Should I be worried about my injectors?

    Build Mods: 5.0 Stroker (stock compression) Roush stage 3 CNC ported heads Stage 3 comp cams Posi Race port eaton @ 14psi LT/full exhaust Intake TB/Plenum H/E Electric water pump Misc odds and ends >>>>60 lb injectors with 2 ford GT pumps and KB BAP<<<< Pump gas I am a little...
  6. fallingup693

    Posi port/ported eaton/stage 3 cam/5.0 stroker dyno

    Currently building up a 5.0 stroker (stock compression). Major mods: a Posi race ported eaton, heavily ported heads, custom stage 3 comp cams from MMR, LT/full exhaust, intake/Accufab TB/plenum running 14 psi. Looking for people that have or have had similar mods to bounce some dyno numbers...
  7. fallingup693

    installing new locks/retainers/springs/valves

    Hey guys I'm having some trouble applying enough pressure to install the keepers onto my valves with the tool that I have. Any suggestions on an easier method or a tool that makes it easier? Thanks in advance.
  8. fallingup693

    Can 60lb injectors support my mods?

    I was running 476rwhp on the same combo but without the ported heads and with the stock blower @14psi but with boost drop-off to 10psi. I'm really concerned about running out of fuel but I don't think the wife will be very happy if I come up with another $400 item to spend money on....lol Here...
  9. fallingup693

    04 Cobra no crank after breakdown

    Hey guys. Just got done rebuilding the top end after a timing chain guide was dislodged and bent all of my valves. Engine would turn before I put the heads on. Everything was fine. Rebuilt the top end. Everything turns over by hand. Hook everything up and it wont even attmpt to crank. Starter...
  10. fallingup693

    4R70W refuses to shift at WOT

    Got a 4R70w auto tranny and tried a WOT run on the highway today and it refuses to downshift or upshift at WOT. Drives/shifts okay at partial throttle. Did notice cruising at about 25mph that it had an ever so slight problem chilling at about 1500 rpm like it wanted to shift but would change its...
  11. fallingup693

    Cylinder #5 not firing

    So I have a problem with the #5 cylinder not firing. So here's what I've done so far. I started unplugging the COP's to see which cylinder wasn't firing. #5 made no difference when I unplugged it so I narrowed it down to that one. Then I swapped the #5 COP with the #6 COP. The end result was the...
  12. fallingup693

    01 GT cylinder #5 no fire issues

    So I have a problem with the #5 cylinder not firing. So here's what I've done so far. I started unplugging the COP's to see which cylinder wasn't firing. #5 made no difference when I unplugged it so I narrowed it down to that one. Then I swapped the #5 COP with the #6 COP. The end result was the...
  13. fallingup693

    FS: Brand New M/T ET II DR's 315/30R18 $550

    You saw the title. Brand new never used Mickey Thompson E.T II's. Selling because they wont fit my wheels. Preferred local pickup/delivery. $550 http://i1267.photobucket.com/albums/jj548/fallingup693/MTETSTREET1.jpg http://i1267.photobucket.com/albums/jj548/fallingup693/MTETSTREET2.jpg...
  14. fallingup693

    04 cobra ticking/clanking

    I have an 04 cobra that has an iron bottom end and a few other mods too long to list. Heads are untouched. I have what seems to be a heat issue. I will start the car, it will run fine for a while. But after the car gets completely up to temp and maybe runs for a while it will start ticking and...
  15. fallingup693

    2001 Cobra intake Manifold P/P stage 2

    Have a 2001 Cobra Intake Manifold upper/lower/spacer ported and polished to stage 2. Looks brand new. $1200 port job. Asking $600 plus s+h. I have receipt. Was going to use it for a turbo build but decided to stick with supercharger. Will have pics up when I get home from work.

Top