Recent content by Dans03C

I have a brand new 26 spline D&D input shaft for sale. Bearing has been pressed on. Asking $175 OBO.

I have a saleen s-281 spoiler that was purchesed for my 03 cobra. I decided aginst using it. never been installed and was just painted black. $250. Iam located in Fremont, Ca. Call me at 510-579-6185 or pm me thanks Dan

I have a one piece s-281 wing i purchased for my 03 cobra. i decided aginst it. Its painted black and has never been installed, also have thired brake light for it. Iam located in SF bay area. I dont want to ship thats why iam trying it in this section. S-281 $300. Thanks

Iam looking to get rid of my tricked out 88cc honda crf 50. I have pics but not sure how to post. Iam looking to see if anyone is interested in working out a trade for a newly steigmeir ported eaton blower(1500mi) off my cobra as well as the 2004 Honda CRF 50 in exchange for a 2.2 Kenne Bell...

I just did a compression check last night not sure what to think. Cylinders 1-4 were 170 to 175 Cylinders 5-7 were 150 to 155 Cylinder 8 was 175 If anybody has any input i would appreciate it. It just seems a litle strange to me. thanks

i NEED TO GET RID OF A 04 HONDA 50. I bought it new but now i just sits. -2004 XR 50 - Takagawa 88cc big bore - BBR Big bore Exhaust - 20mm Kehin Carb - Takagawa rev box - Takagawa intake - BBR HD Clutch Springs & Clutch Disks - Fast50s Billet Throttle - Fast50s Bars - BBR SP5...

I just got back from making a dyno run, and now have some concerns. My last dyno showed 488/505 Todays dyno 454/458 WTF Tune is perfect car seems to be running great. My question is could a slipping clutch cause this?

I finally got my car finished, and dyno tuned yesterday. Im running a 2.93- 4lb, Stieg Ported blower-Pl, Accufab, UPR CAI, Bassani catted X, Bassani cat back. I made 486rwhp- 505rwhp. Mind u this is on 91 octane, do these #s seem about right, or a little low. My A/F is right at 11.9-12. Any...

I just got my car tuned today made 486rwhp and 505rwtq. This is with a 2.93- 4lb , with a steige ported blower. Does this seem low to u.

Just got my car tuned today and made 487rwhp/505rwtq at 16lbs of boost. My set up is the steige ported blower, 2.93-4lb lower, Accufab tb. bassani x w/cats, bassani catback. Feels like a different car. Do these #s seem about right for a California car.

I just installed my Ported steig blower, and Plenum, 4lb lower, 2.93 upper. My car also has bassani x with bassani catback. Question is what would be a safe gap for the IT 22s. I am trying to avoid any blow out problems. right now they installed and gapped at 36. I heard between 32-42 is the...

Not sure if i need 55 or 60 lb injectors or maybe stock will be fine, im not sure. Im in the prosses of putting my car together(Stieg poted blower and Plenum, Accufab TB, SCT big air, 2.93 - 4lb lower, IT 22s, KB BAP, Bassani Catted X, Bassani Catback) Any help would be great thanks.

I am curious on what i can use to clean the gasket between the blower and the lower intake. I just want to make sure i dont mess it up.

Is ok to RTV all the way around the intercooler instead of just doing it in one corner as specified in instructions. I dont think it much matters im just curious. Going to put my blower back on tomarrow, tring to get all the loose ends tanken care of. Thanks

My question is wether or not i need the 20 amp or the 40 amp boost a pump for a steig ported blower.