Recent content by cobra9903

Just got back form the dyno Its a 2.3 whipple gen 2, 2.8 RR pulley, 93 pump gas, on 17 degrees of timing. The temp out was around mid 80s. The car made 599 HP and 521 Torque. I was getting around 585 HP, and then on the last run we turned on the killer chiller and let it idle for about 10 min...

Like it says looking for a 2.75 pulley for a 2.3 whipple. Let me know what you have. Thanks!

Just wanted to see if anyone else has had this problem. I am assuming Its because of the UPR K member must have brought the motor up a tad, but the throttle bracket on the whipple is scraping the hood. Going to mod the bracket to make it fit. Just wanted to give everyone that has a 2.3 whipple...

So I installed the blower to find out that I pretty sure the boost bypass valve isn't working. Is hard to see but I marked the arm with a marker and its not moving at all. I assume it should open as soon as the car starts, I have not taken the car out for a drive but it Idles fine and pulls...

http://www.svtperformance.com/forums/showthread.php?1011013-Parts-for-sale-for-pickup-in-Ohio-CCW-rims-Prochamber-Midpipe-ect!

Parts for sale for pickup in Ohio, ported stage 6, Prochamber Midpipe,ect! Selling some parts to fund new fuel setup. Ported stage 6 blower with torque plate just rebuilt by johnny's porting. Looking for around 800 picked up! The prochamber make me an offer just keep in mind as of now...

I finally got around and spent Saturday and installed my Mac long tube headers along with a mac prochamber mid pipe. The are ran through a magnaflow catback with dumps. The sound is not that much louder than it was before at idle but you get some more sound when you get into it. As far as...

http://www.svtperformance.com/forums/terminator-parts-buy-sell-242/1003694-eibach-pro-kit-springs-pickup-ohio.html

I have a set of eibach pro kit springs backs have around 600 miles on them fronts have maybe 1000 miles on them. I switched to a SRA and now have ford racing C springs. I at this point do not wana mess with shipping, between work and kid just don't wana mess with it. Looking for $150.00 or...

Pictures of the 78 F100 I finished up thought I would post some pictures of the F100 I finished for a customer. The body seams where all shaved and filled in, deleted the antenna, built the cowl hood, and gave it a nice paint job. The truck was leaving us and heading to get new carpet, sound...

I couldn't help it anymore the temp was almost 60 out so I had to go for a drive, just thought I would post some pics while I had it out. I had quite a few parts to put on this year and I still have a few left to put on. I installed the new wheels, sequential and smokes tail lights, Raxiom...

Well I got my tires mounted on the rims today and put two on the car to see what its gona look like. I will get better pics when I get the other two on and get the car outside. All in all the rims are a nice design and seem to be made very well. I only had to have three rim sent out to get a...

I know this has been beat to death and I'm not trying to start anything but I just put a solid axle out of a Mach1 and all I can say is wow. One of the best mods Ive done so far. I was kinda worried about losing some ride quality but to my surprise its better now. I went form a full bushing...

Looking to sell my IRS out or the mustang. The mods are as follows Maximum motorsports Delrin rear upper & lower control arm bushings,MM IRS subframe bushing,MM IRS adjustable tie-end kit,MM rear swaybar bushings & end link kit,MM urethane differential mounts,MM low profile IRS subframe...

one of a kind 03 cobra FS/maybe trade I've been thinking about selling my 03 cobra. The car has 24000 miles, has custom body mod that you will not see on another car. The gas door has been relocated to the sail panal, the quarters have been extended to match the molded in cobra spoiler, all the...