Recent content by cobra=trouble

  1. C

    Shifter & A C4 ???

    never mind who the **** gets on here anymore?
  2. C

    pictures of the underside of the valve covers baffling.

    I cant remember what they look like ? Does anyone have problems with oil being sucked into the engine? And also i have oil going to the passenger side breather hose into the TB.
  3. C

    Where's the first speed gear and slider located?

    .....
  4. C

    Try this , and report back please.

    When your ( T56 ) cobra is idling push in clutch and go into first gear immediately. Does it grind ? Or go into first with no problems whatsoever with no grinding ? Thanks . Trying to see if I have an issue or not. My Cobra I have to wait at least 6 to10 seconds before mine dont grind...
  5. C

    03/04 IRS Steeda Cobra rear coil springs

    I have replaced my IRS with A SRA about 800 miles after getting this kit . So am I have 2 for sale if somebody wants to buy them . Asking 100 shipped in lower 48. Pm me Mods. Please move to proper place .
  6. C

    correct T 56 fluid ?

    Ok, after my recent motor rebuid. I put Amosil synthetic in it . after about 800 miles. I started to notice when I go into first gear at a stop and dont wait long enough for the input shaft to stop turning all the way it grinds. If I go to second then to first it does fine. Sorta like the old...
  7. C

    Aftermarket 351w 9.500 block ? 's

    Never mind. Seems 58 people have No idea
  8. C

    steeda PCV oil separator install ?

    I have one I need to install I was looking at hoses on the separater there small. WhereI. does. this tie into ? I had for over a year lost instructions. I don't think it goes into the big hoes going to the vavle cover . I see smaller hoses similar behind my kb 2.6 dose it. Tee into that...
  9. C

    Cobra , trailer, & Winches

    What's the least lb. Rating to get a Cobra up on a trailer. I say Cobra thats my Heaviest car. I just got a used car tralier. Am looking at HF. cause of low funds means lowest prices. I dont think a ATV or a UTV winch is going to cut it , even with the good reviews I read. Thanks was looking...
  10. C

    Thats right. I Want the Quietest Muffer.

    I used to like it Loud, I have Borla Stingers. Cops follow me home everyone I take it out close to the house people report me 2 times in 3 weeks , but only drove it twice.What Mufflers are the quitest.While still having good flow. Wife wants me to sell car. Cause of this. This is no B/S. Thanks
  11. C

    Reasons, why you hate spec 3 plus.

    1. I have of one of these units. I have about 700 miles on it , with aluminum FW. Not all stop and go traffic breakin. But my car I don't know what it is . It feels as if you going to get bucked off a Bull. You have to get used to it but still Bucks at times. I let my brother inlaw drive it I...
  12. C

    coyote and 4.6 4V. Bell housing ?

    Are they the same bolt pattern? Thanks
  13. C

    Any automatic Mach 1's want a T56 swap?

    I have a 2003 Cobra 33, 000 miles .was all stock for 27, 000 miles. I need to go to an automatic .due to bad back, hips, and knees. I need shifter and all whatever it takes to do the swap. I just had 26 spline input shaft installed in it with new spec 3 plus clutch. Tri axe shifter. And...
  14. C

    want to go automatic ?

    Reason being, I hurt my back in May it has not been the same while. I push on the clutch I I can feel it in my back. Still to this day, I'd hate to sell to cause of this. I been looking at my a Summit catalog. In the newest one on page 200 .I see a PA 4R70W PN# PMA-PASS45103 Its says for...
  15. C

    Cobra build done at last runs after 1000 days

    Yep. Drove it a little today. Got to got Insurance and tags on it next week. Thanks to those who Actually helped me through my build. will post pics of build.and cost and part list one day soon. From home PC. I still only had break in tune .from Eric Brooks
See more

Top