Recent content by Chappy

  1. C

    Wiring Question - Air Conditioning Activation

    FYI for anyone that might be looking for this info in the future. Supply 12v to pin 41 from your ac pressure switch, then ground your compressor relay on pin 69, that’s it. On my datalog last night when I do this the compressor activation is logged, I see the rpm adder for AC signal increase...
  2. C

    Wiring Question - Air Conditioning Activation

    I've dropped an 03 Cobra engine into my 1970 Mustang. I'm using a detail zone engine harness for the car. Everything is wired up and working great, except for when I turn on my AC the engine doesn't know it's on so it idles down low and will stall out sometimes. I'm trying to understand what...
  3. C

    Stalling with AC on - datalog questions

    Thanks for the responses guys. Guess I should have added a little more detail. I’m not tuning the car myself, using a well known tuner for remote tuning. Datalogging signals per his request, sending him logs, uploading turns as needed. The car is actually a 70 Mustang, running a detail...
  4. C

    Stalling with AC on - datalog questions

    Anyone good with reading datalogs? Got an issue with my car stalling out with the AC on when you close the throttle from like 2k rpm or higher. The engine just almost immediately stops. This can happen sitting in the garage, so no load from driving. When looking at data logs, the only...
  5. C

    Moving to NorCal, and good local car forums?

    Hey all, I'm going to be relocating to the NorCal (Palo Alto, San Jose, Fremont) area here in the next couple of weeks. Was wondering if there were any local car forum sites to join to get in with the local car scene? Initially I'm going to be bringing my 1970 Mustang Fastback project with...
  6. C

    1 15x3.5 Greg Weld Racelite Chrome Wheel, Shank Lugs

    I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. 1 - new Greg Weld Racelite 15x3.5, 5 lug (4.5 and 4.75") chrome wheel including center cap. Looking $100 shipped...
  7. C

    Diff Cover/GSS392 Pumps/3.31 Gears/

    I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. Stock 3.31 Rear gears, only have 5K miles. $45 2 Walbro GSS 392 external 255lhp fuel pumps. Both come with...
  8. C

    Stock Driveshaft/Emmissions Parts/TA Cover/Gears

    I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. Stock 3.31 Rear gears, only have 5K miles. $50 Stock Transmission crossmember - $50
  9. C

    1 - 17x10.5 Anthracite FR500

    sold
  10. C

    HE/Accufab/Mystichrome Seat/Rad/Fan/Oil Cooler/Clutches/SC Coolant Tank/Etc

    I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. Stock Fan assembly - $65 for the fan Stock Pulley guard. In really good shape, barely looks installed. $45...
  11. C

    Pulley/Hub Identification

    I purchased a used blower a while back that had a 2.8" pulley and hub assembly on it. I'm looking to get a 2.93" pulley for the setup, but I'm having a hard time locating a pulley that will fit the hub. My current pulley has a 33mm hole in the center of it. 4 bolts attach the pulley to...
  12. C

    WTB - Stock Trans Mount

    Anyone got a stock trans mount they would like to sell? If so, send me a PM with price shipped to 46033. Thanks
  13. C

    Beech Bend Raceway Flooded

    Not sure if any of you have seen it or not, but the track is flooded really bad. By the pictures I would say there is at least 15ft of water on the track, maybe more. Hopefully they can recover from it quickly. Local Racing News and Rumors by ODELL: POSTED 5-3-10 FLOOD OF 2010 AT BEECH...
  14. C

    IAC Relocation Anyone?

    Anyone done an IAC relocation on their car? I'm doing a custom install where I would like to remove the IAC from the top of the plenum completely. Would it be as easy as just plumbing a port from before and after the TB to a plate where the IAC installs? Thanks in advance.
  15. C

    2 10lb NX Bottles

    White 10lb NX bottle - $100 + shipping 10lb NX bottle that has been professionally painted back. Very glossy, some minor scratches/scuffs from being installed in brackets, great shape otherwise. $150 + shipping If local each bottle still has 3-4lbs of nitrous left in them. If I...

Top