Recent content by CHAOS 2

1967 mustang coupe If you want a car you can you can take on a couple hour cruise then go to the racetrack and run mid 10s. in the quarter mile on 17in wheels or want to throw some slicks on turn on the nitrous and bust off some low 9s. this is the car for you. Best as pictured 10.68@129 n/a...

1967 mustang coupe If you want a car you can you can take on a couple hour cruise then go to the racetrack and run mid 10s. in the quarter mile on 17in wheels or want to throw some slicks on turn on the nitrous and bust off some low 9s. this is the car for you. Best as pictured 10.68@129 n/a...

1967 mustang coupe If you want a car you can you can take on a couple hour cruise then go to the racetrack and run mid 10s. in the quarter mile on 17in wheels or want to throw some slicks on turn on the nitrous and bust off some low 9s. this is the car for you. Best as pictured 10.68@129 n/a...

i have a 2003 cobra motor fully rebuilt its my friends motor. had a bad injector fried one piston had the motor completly gone through bored .20 over with new manley 2618 platinum pistons stock manley rod and cobra crank . heads were rebuilt also with comp. upgraded springs and retainers and...

SELLING FOR A FRIEND A 93 GT ITS THE PERFECT SLEEPER BODY IS COMPLETLY STOCK ON THE OUTSIDE. EVERYTHING UNDER IS BUILT MOTOR 97 COBRA 4V 281 WITH 38,000 MILES MEZERINE WATERPUMP BBK THROTTLEBODY 55LB INJECTORS SCT 2400 MASS AIR METER DRIVETRAIN REBUILT T-45 CENTERFORCE CLUTCH...

-------------------------------------------------------------------------------- i hate to do it but i just ont have time to finish it and i just want to ride now. ive got a 93 gt 68,000 original miles almost perfect red with black interior interior is 9.75 out of 10 exterior is 8.5 out of...

cnc ported b style heads new guides, seals no valves or followers 980.00 obo. 4v cams regrinds 206int. 206 exh. @.50 114 lsa 445 lift 400.00 obo stock intake good condition 400.00 obo. many other stock 4v parts laying around just ask i might have it i need these sold make me some...

Trader Feedback: (2) Join Date: Jun 2004 Location: salisbury,Maryland Posts: 377 cnc ported cobra heads, custom cams -------------------------------------------------------------------------------- ive got a set of fully cnc ported b heads these fit 96-98 cobras used on a...

Ive got a set of fully cnc ported b heads these fit 96-98 cobras used on a turbo car for about 15 passes and a few dyno runs car ran 8.80s at over 160mph so i know they will make power their bare no valves or springs bronze guides the flow numbers are 320 int. 255 exh. @ 550. i also have a...

Ive got a set of fully cnc ported b heads these fit 96-98 cobras used on a turbo car for about 15 passes and a few dyno runs car ran 8.80s at over 160mph so i know they will make power their bare no valves or springs bronze guides the flow numbers are 320 int. 255 exh. @ 550. i know long have...

Ive got a set of fully cnc ported b heads these fit 96-98 cobras used on a turbo car for about 15 passes and a few dyno runs car ran 8.80s at over 160mph so i know they will make power their bare no valves or springs bronze guides the flow numbers are 320 int. 255 exh. @ 550. i know long have...

just bought a tweecer dont think its an rt bought it used dont really no how to tell im just frusted theirs so little information for eecv systems.if someone could tell me or point me in the right direction ive been to all the forums and websites i know people are doing it but it seems like...