Recent content by allmotorTA

Sold

Stock 2001 cobra upper and lower intake manifold. Removed to install a ported short runner. No sensors included. $250 shipped

Installing a ported short runner on my '01 this week. Any install guides out there? I'm pretty good with a wrench but I just like to have an install guide when I can. Like to know the ft pounds recommended for intake bolts, etc etc. Also, as I understand most people inspect then reuse the intake...

*******SOLD******** I have two fr500 m58 mufflers 2.5" in 2.5" out. Dual mode, quiet at part throttle but open up and are loud at WOT. Discontinued and rare. 409 stainless so surface rust is inevitable but they will last a long time. They will clean up better but I haven't tried to do so. $110...

Have both of these, complete, ready to bolt on. Both are in great shape. Only ding/dent is on the bottom of one of the flowmaster mufflers and is shown in the last pic below. These will only fit IRS equipped mustangs. Will not work with a solid axle. Flowmaster- $250 SLP- $275 I will also...

First pic is when I picked it up. Second pic is after I added tint, 18x10 and 18x9 fr500's, and took off the rear spoiler and Mach 1 chin spoiler. Also took off the x pipe and slp lm catback and replaced it with an off road h pipe and flowmaster catback. What can i say, im an h pipe/flows kinda...

Just as the title states. Just seeing if they are compatible. Thanks!

Like the title says, anyone near Newark that can go look over and test drive an '01 Cobra for me? Planning on sending payment and shipping this car to me. Would like to at least have someone drive it first. This weekend would work best. He is available Friday night, all day Saturday and Sunday...

Hello, I bought a predator tuner from someone on here and went to install it. BTW, he said it came with a custom amazon tune if that helps as well. When I went to install it it said it was not licensed for use with this vehicle. Now, I know you need to un-marry the predator from your car...

Finally made it out to us41 again: 60' 1.73 1/8 7.637 @ 94.75 1/4 11.82 @ 117.86 This was on et streets. The track was dead hooking, absolutely no sign of spin or wheel hop. My mods are in my sig. The bad thing is, it detonates the whole way down the track. I think the cool air leaned it...

Well, here's the story: I went to the track a little while back and went 12.0 @ 118 on Nittos. I finally was able to go back again 3 days ago and went 11.99 @ 115 on ET streets. The differences between the 2 runs are as follows: I swapped out my densecharger for a K&N FIPK and I installed some...

Edit: I'm just gonna roll with it... I think that's how it is supposed to look. It's sealing.... I thought 03 cobra mobil 1 filters are M1-210... Well, I threaded it on and it is not long enough. It is hand tight, but the end with the rubber seal is still almost a quarter of an inch from...

I want to pick up 2 factory 16" mustang wheels to toss some 11.5 or 10.5 ET streets on. What wheels should I look for? What width should be the minimum for both the 10.5's and 11.5's? Any help would be appreciated :beer:

Anyone have a pulley puller I could use to toss on my 2.80? I could drive over, toss my 2.80 on, and I'll be on my way :beer:

Finally made it out to the track tonight... 03 Cobra, just bought it 2 weeks ago, 1200 miles, all stock except Densecharger, off road H, and flowmaster CB. I was completely babying it all the way down, no powershifting. I tried powershifting but it was wheel-hoppong like crazy, especially on the...