Stiegemeier snake bite

bigdog93lx

Gallons per mile
Established Member
Joined
Apr 26, 2003
Messages
1,973
Location
North shore MA
you can get a set of nice looking bbk longtubes for 450 shipped.

Dont waste your money. I have them on my car. You can't pull the tranny with em on. An the "ceramic" coating is all peeling off on the collector. I think "ceramic" is just the color of spray paint they use. Save your money for good headers and do it right once.
 

mitrls10

"Torqued Motorsports"
Established Member
Joined
Jun 25, 2009
Messages
246
Location
Leesburg, Ga
I have a set of mac longtubes on mine and were $650 and the ceramic coating has held up nice and will polish out if I were to actually clean them lol.
 

MustangThief

Active Member
Established Member
Joined
Nov 8, 2005
Messages
1,387
Location
Location, Location...
Since Bob requires LT's and a race tune to hit 550rwhp with Snakebite, what would a Stage IV or V Steggy do once you added LT's and some Torco...i know many stage 5's have hit 515-520 without LT's and Torco, so i would assume that adding those 2 things would get you pretty damn close to the 550rwhp Snakebite is aiming for.:shrug:

Lol. I'm at 503/502 with stg V, 2.8 upper, o/r x-pipe and CAI as my power mods. It's funny you said that cuz I was really hoping for 515-520 if I added some MAC LTs.

My car is tuned for 93 though, but I run Sunoco94.

That's my plan for my next mod. After my FLSFCs get put on soon anyway :p
 

fudgerunyard

Banned
Joined
Apr 11, 2009
Messages
158
Location
orlando
Lol. I'm at 503/502 with stg V, 2.8 upper, o/r x-pipe and CAI as my power mods. It's funny you said that cuz I was really hoping for 515-520 if I added some MAC LTs.

My car is tuned for 93 though, but I run Sunoco94.

That's my plan for my next mod. After my FLSFCs get put on soon anyway :p

If those numbers are from a Mustang Dyno like your sig says, then your pushing well over 503/502.
 

Venimus03

...................
Established Member
Joined
Nov 9, 2004
Messages
3,617
Location
VA
Ok, enough of this. Send me the snake bite port and I'll show everyone what its capable of during the terminator shootout! :beer:
 

dynobobstieg

New Member
Joined
Aug 26, 2004
Messages
4,153
Location
st. charles mo
So what does it take to not be approved for the Snakebite? It seems to me that everyone who has applied has been approved.

Submit your mods and information we will go over them, we had some computer complications and some of you may not have got the email.
It is best if Bob has your information in front of him and then he will be able to speak to you on the phone and go over more details/information with you. (Too much boost in some cases)

Thank you
Snake Bite(tm) Spec Sheet

StiegeSplash
636-949-2275
[email protected]
 
Last edited by a moderator:

fudgerunyard

Banned
Joined
Apr 11, 2009
Messages
158
Location
orlando
Need not worry, guys. Everybody and their brother who wants one will be able to get one in short order. This has all been merely a marketing ploy to drum up interest that has gone awry. My guess is Stieg won't be turning down anybody's $1,500.
 

Tractionless1

Active Member
Established Member
Joined
Jun 28, 2007
Messages
6,755
Location
Atlantic Southeast
(Too much boost in some cases)

Thank you
Snake Bite(tm) Spec Sheet

StiegeSplash
636-949-2275
[email protected]

I don't get it, boost can be reduced in the matter of an hour by replacing a lower pulley ring or upper at the blower. I'd love to run less boost and make more power.

What is the problem with running "too much boost"?

Silverboost,
As you can tell I got turned down, too much boost I guess (18.89psi).
 
Last edited:

CobraMac

Active Member
Established Member
Joined
Dec 16, 2006
Messages
3,046
Location
Orange County, CA
I don't get it, boost can be reduced in the matter of an hour by replacing a lower pulley ring or upper at the blower. I'd love to run less boost and make more power.

What is the problem with running "too much boost"?

Silverboost,
As you can tell I got turned down, too much boost I guess (18.89psi).

You were turned down becuase he doesn't think you would be able to pay the $1500 :lol1: just kidding man......I don't understand ANY of this especially since there's still no specs or anything. If I was in the situation to be able to get one...I would've jumped ship a couple weeks ago one I saw all the goings on in this thread
 

Users who are viewing this thread



Top