Epic Build Thread: CPr Single Turbo + MMR Pro Mod 1500 block with extras!!

Rochambo

New Member
Established Member
Joined
Feb 9, 2014
Messages
115
Location
Tampa, FL
Very nice build, but this is why I couldn't do something this intense. It's my DD and it just takes too long!

Very nice though.
 

CPRsm

Active Member
Joined
Feb 3, 2009
Messages
4,400
Location
San Diego, Ca
It's not bad when you have all the parts waiting. But when you blow up your DD, then decide to build a 1000rwhp+ car, takes a bit more time lol
 

notchy444

New Member
Established Member
Joined
Oct 26, 2012
Messages
285
Location
San Diego, California, United States
Sorry!!! Havnt been updating for a bit... Got a bunch of other parts ordered that I wasnt really planing on / forgot I needed! Going for over 1000+rwh need a lot of supporting mods you really dont think about before the build starts. I needed a ATI super damper, Carbon fiber drive shaft, and fix up the rear suspension while the cars was down. In all honesty of I would of ordered the parts while the engine was being built from MMR my car would of been done by now hahaha. But didnt think it would take 3 months to get my block but I know the wait will pay off! Last parts all come in this week and drive shaft should be in next week, Hopefully get it on the dyno asap and start tuning soon! Heres some old pic of the headers in that sexy flat black! Ill get more pics of the turbo and hot side piping mounted with the finish on em.

Headers2_zps12084422.jpg


Headers1_zpsc457a0ef.jpg


Headers3_zps0166e365.jpg
 
Last edited:

muchv8wow

New Member
Established Member
Joined
Mar 16, 2014
Messages
83
Location
Florida
Oh man this is an insane build, I just went through all six pages and I'm in love haha, is this mainly set up for drag? I feel not because you've mentioned street roll races so youll have a blast if you go to the next texas mile!
 

notchy444

New Member
Established Member
Joined
Oct 26, 2012
Messages
285
Location
San Diego, California, United States
Oh man this is an insane build, I just went through all six pages and I'm in love haha, is this mainly set up for drag? I feel not because you've mentioned street roll races so youll have a blast if you go to the next texas mile!

Thanks! This is for a mix of drag racing and DD because street car!! I do plan to take this car to the Texas mile eventually when I go full retard. The kung fu is strong in this build just wait and see :rockon:
 

CPRsm

Active Member
Joined
Feb 3, 2009
Messages
4,400
Location
San Diego, Ca
dual gates? single 50 not enough or just testing things?
Little of both. Have the 60mm on there because the 50 wasn't cutting it w the new turbos. The second flange is just there incase when the car is turned up. If it can't keep up we'll punch the hole and add the gate. The turbo company is developing bigger and badder all the time. So the second gate is juuuuuuust in case lol
 
Last edited:

notchy444

New Member
Established Member
Joined
Oct 26, 2012
Messages
285
Location
San Diego, California, United States
Getting super close!!! The beast started up and ran great today! Got the base tune and took it for a spin. Didnt stall or buck, Getting the crank relearn done then strapping her to the dyno to break this engine in properly! here is a Video the car running with a dumped down pipe.

[video=youtube;-d8565N7wlg]https://www.youtube.com/watch?v=-d8565N7wlg[/video]
 

CPRsm

Active Member
Joined
Feb 3, 2009
Messages
4,400
Location
San Diego, Ca
Oh yeah, it's not done. Quick fire and look for smoke lol. Everything was good so we'll finish the install. When HIS actual turbo come in the blanket will go on. We'll take that ugly prototype intercooler off and put the a/w on, and black out the maf tube as well. On the route to buttoning up, tune and beautification haha
 

Users who are viewing this thread



Top