Yet another TT Cobra build..

Greg@RET

New Member
Established Member
Joined
Mar 30, 2005
Messages
1,931
Location
SoCal
Posting this for a customer, he doesn't post. Built shortblock, stock heads/cams, triple return fuel set up. The Kmember came in yesterday, so the car is coming along nicely.

turbo2.gif


TTbuilds002.gif


TTbuilds003.gif


TTbuilds006.gif


TTbuilds005.gif

Pulling the IRS for a built solid.
TTbuilds001.gif
 

Greg@RET

New Member
Established Member
Joined
Mar 30, 2005
Messages
1,931
Location
SoCal
Heres another update 5 business days later.... dont ask about the bottle, customers choice not mine lol

Twin disk.. he didnt want to upgrade the spline but we changed the TOB sleeve.
TTbuilds007.gif


TTbuilds008.gif


TTbuilds.gif


TTbuilds013.gif


TTbuilds014.gif


TTbuilds016.gif


Customer dropped the line lock off, to bad it wasnt here when the motor was out lol.
TTbuilds015.gif



TTbuilds017.gif


fuelsys.gif


fuelpumps.gif


Fuel system just about done...

TTbuilds030.gif


TTbuilds031.gif


TTbuilds028.gif


Rear end was dropped off at the shop today...
TTbuilds029.gif
 

Teej281

Active Member
Established Member
Joined
Aug 6, 2007
Messages
2,010
Location
Hanover, PA
Damn, a lot less clutter than an IRS :D lol but nice build! So the guy didnt want to upgrade to a 26 spline input shaft...but is wanting to run twin turbos with nitrous?! This guy is just stupid.
 

90goldtsiawd

here 4 da laffs & cruelty
Established Member
Joined
Jun 12, 2006
Messages
7,410
Location
NJ
Damn, a lot less clutter than an IRS :D lol but nice build! So the guy didnt want to upgrade to a 26 spline input shaft...but is wanting to run twin turbos with nitrous?! This guy is just stupid.

Yeah wtf is he thinking? Did you guys try to sway him to upgrade it now?

Also, what size turbos are those?
 

LuDamiKE81

Flattest of the Flat
Established Member
Joined
Oct 24, 2006
Messages
3,889
Location
New Orleans
Nice build! Its going to suck to have to tell him i told you so...should have went with the 26 spline lol. Ive been through 10s and im just a run of the mill pullied cobra, but to each their own.
 

ruthless

Turbo Terminator and TVS Terminator Vert
Established Member
Joined
Jun 2, 2007
Messages
1,439
Location
North of Pittsburgh, Pa
Very nice build! :beer:

Ok what a sec...
Fore tripple return fuel system Check
Solid rear Check
twin turbo Check
twin disk clutch Check
Nitrous Check
Built engine Check

But no upgraded input shaft. :bored:

Plus you had the tranny apart for the TOB sleeve so whats another couple hundred bucks for the 26 spline input shaft. Now if the owner wants it upgraded it not going to work with that clutch setup. Not the area I would have cut a corner on when the rest of the car is built so well. I would have went with the tripple hat and only ran 2 pumps and got the input shaft upgraded if I ran out of money.

Oh my head hurts!!
 

Greg@RET

New Member
Established Member
Joined
Mar 30, 2005
Messages
1,931
Location
SoCal
Whats the saying.... you can lead a horse to the trough but you cant make him drink lol

All I know is there is a spitting Cobra in the shop...
[nomedia="http://www.youtube.com/watch?v=FS-KFlkvdO0"]YouTube - Spitting Cobra[/nomedia]
 

Blown2004Stang

Active Member
Established Member
Joined
Nov 27, 2009
Messages
1,034
Location
Katy, TX
I would have added 150 bucks somewhere in the ticket, and put the 26 spline shaft in as a "free upgrade".. ;) Seriously.. The first time he launches the car on sticky tires, it's going to wrench the input shaft right in two!
 

Greg@RET

New Member
Established Member
Joined
Mar 30, 2005
Messages
1,931
Location
SoCal
Just need to finish up the little odds and ends now. It will need some down pipes made, the used ones it came with are not even close.
 

Drazga

New Member
Established Member
Joined
Sep 28, 2009
Messages
616
Location
Dirty Jersey
why wouldnt he do coilovers in the rear too? where did you get the rear from? looks clean good work.
 

Greg@RET

New Member
Established Member
Joined
Mar 30, 2005
Messages
1,931
Location
SoCal
Little update.... just need to make a pipe from the maf to the intake, then make some down pipes, then throw on some breathers.

IMG_20101110_125141.jpg


IMG_20101110_130144.jpg


IMG_20101110_130158.jpg


IMG_20101110_130412.jpg
 

Users who are viewing this thread



Top